EN
Plastic tube welding machine
Fig. 1-2
1 Supporting stand
2 Temperature adjusting screw
3 Handle
4 Heating element
5 Welding tools (heating spigot + socket)
6 Green power-on indicator lamp
7 Red temperature indicator lamp
Fig. 3
(1) Preparations
(2) Heating element
(3) Sleeve
(4) Heating spigot
(5) Heating socket
(6) Pipe
(7) Heating
(8) Completed joint
1. GENERAL POWER TOOL SAFETY WARN-
INGS
WARNING
To reduce the risk of injury, the user must read and un-
derstand the instruction manual.
Read all instructions. Failure to follow all instructions list-
ed below may result in electric shock, fire and/or serious
injury. The term "power tool" in all of the warnings listed
below refers to your mains operated (corded) power tool
or battery operated (cordless) power tool, also machines
and electric units. Only use the power tool for the pur-
pose for which it was intended, with the due attention to
the general safety and accident prevention regulations.
KEEP ALL SAFETY NOTES AND INSTRUCTIONS FOR
THE FUTURE.
A) Work area
a) Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable liq-
uids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose con-
trol.
B) Electrical safety
a) Power tool plugs must match the outlet. Never modi-
fy the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of elec-
tric shock. If the power tool comes with an earthed
wire, the plug may only be connected to an earthed
receptacle. At work sites, in damp surroundings, in
the open or in the case of comparable types of use,
only operate the power tool off the mains using a 30
mA fault current protected switch (FI breaker).
b) Avoid body contact with earthed or grounded surfac-
es such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for carry-
ing, pulling or unplugging the power tool. Keep cord
away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an ex-
tension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
C) Personal safety
This appliance is not intended for use by persons (in-
cluding children) with reduced physical, sensory or men-
tal capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
a) Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not use
a power tool while you are tired or under the influ-
ence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b) Use safety equipment. Always wear eye protec-
tion. Safety equipment such as dust mask, non skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the
off position before plugging in. Carrying power tools
with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in per-
sonal injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
7