Roller Fox ANC Notice D'utilisation page 12

eng
(16), insert the Allen key in the holder (15). This adjustment possibility allows
better utilisation of partially blunt saw blades and prevents the tip of the saw
blade from hitting a wall/inside of a pipe (take saw blade stroke into consid-
eration).
3. Operation
Use eye protection
Use ear protection
WARNING
Suitable dust extractors, a respirator and disposable overalls must be used for
work which could produce health hazardous dusts. Observe the national regu-
lations.
ROLLER'S Fox ANC: Switch on/off with on/off safety switch (7).
ROLLER'S "VE" reciprocating saws: Stepless electronic stroke speed control
by variable pressure on the stepless safety switch (accelerator switch) (10).
ROLLER'S Fox ANC SR: Stepless electronic stroke speed control. Preselec-
tion of the desired number of strokes at the thumbwheel (12). Switch on/off
with on/off safety switch (7).
3.1. Work procedure for sawing with a guide holder
WARNING
Only hold the ROLLER'S reciprocating saw by the insulated handles ("A") (Fig.
1), not on the guide holder (2), when performing work where the tool can come
into contact with concealed electric cables or its own power cable. Contact with
a live cable can also put metal tools or the guide holder under voltage and lead
to electric shock.
NOTICE
Only use ROLLER'S special saw blades (see 2.4.). Normal saw blades with
one-sided hinge are useless for right-angled sawing with a guide holder because
they break at the clamping point due to high thrust pressure.
Fit the guide holder as described in 2.2. Place the ROLLER'S reciprocating
saw with guide holder on the pipe so that the clamping spindle with toggle (1)
is vertical. Tighten the clamping spindle. Press the switch (7 or 10) at the same
time as grasping the motor handle or actuate the lever with latch (11) and pull
up the ROLLER'S reciprocating saw until the pipe or profile is sawn through.
The start of sawing can be improved especially with large diameters (e.g. 4")
by not switching on the ROLLER'S reciprocating saw until the saw blade is
already in contact with the pipe. Make sure that the prism of the guide holder
is always kept free from chips, otherwise the right-angled cut will be impaired.
To achieve optimum sawing speed and to preserve the saw blade, only select
medium thrust pressure. Heavy thrust pressure does not increase the sawing
speed! ROLLER'S Fox ANC is equipped with an overload protection (8). This
is triggered when the thrust pressure is too great; the button jumps out slightly
and the ROLLER'S reciprocating saw stops. After a few seconds the overload
protection can be pushed back in and the ROLLER'S reciprocating saw can
be switched back on.
3.2. Work procedure for hand-guided sawing
WARNING
Only hold the ROLLER'S reciprocating saw by the insulated handles ("A") (Fig.
1) when performing work where the tool can come into contact with concealed
electric cables or its own power cable. Contact with a live cable can also put
metal tools under voltage and lead to electric shock.
For straight or curved cuts press the tiltable support shoe (6) forcefully against
the material so that the tiltable support shoe (6) is constantly in contact with
the material to be sawn. Switch on the ROLLER'S reciprocating saw. Only use
sharp and flawless saw blades. Even thrust pressure reduces the risk of acci-
dent and is kind on the ROLLER'S reciprocating saw and the saw blade. Always
feed the connecting lead back away from the ROLLER'S reciprocating saw.
Keep the ROLLER'S reciprocating saw pressed forcefully against the material
to be sawn during sawing. If the saw blade jams whilst sawing, switch off the
ROLLER'S reciprocating saw, widen the sawn cleft with a suitable tool and pull
out the saw blade.
For plunge-cut sawing in material that is not too hard, e.g. wood, plastic, plastic
pipes or alloy pipes, the saw blade can be plunged carefully into a surface
whilst sawing (Fig. 4). Use a short saw blade. Place the switched off ROLLER'S
reciprocating saw with the bottom edge of the tiltable support shoe (6) and the
tip of the saw blade at the cutting point, switch on the ROLLER'S reciprocating
saw and plunge the saw slowly sawing into the material. Preferably use
ROLLER'S reciprocating saws with stepless electronic stroke speed control.
In harder material, e.g. metal, an appropriately large hole for the saw blade
should be drilled for the sawing start.
3.3. Lubricants
Do not use lubricants for normal sawing work. These hinder the ejection of
chips from the sawing chase and therefore reduce the useful life of the saw
blade.
12
4. Maintenance
Use a respirator
4.1. Maintenance
4.2. Inspection/Servicing
ROLLER'S Smaragdol or ROLLER'S Rubinol for cooling and lubrication should
be used exclusively for sawing stainless steel and hard cast iron pipes. It is
recommended to use ROLLER'S Fox ANC SR and one of the ROLLER'S special
saw blades 561003 ... 561005. The guide holder is absolutely essential for
right-angled sawing (see 2.2.).
WARNING
Before any repair work, pull the mains plug!
The ROLLER'S reciprocating saws are maintenance-free. The gear runs in a
life-long grease filling and therefore needs no lubrication. Keep the saw blade
holder clean. Remove chips from the housing of the saw blade holder. Remove
water/moisture from the housing of the saw blade holder after every use. Lightly
lubricate the saw blade holder and saw blade clamping lever (14) with machine
oil (only ROLLER'S Shark VE). Change a defective locking screw (9) (except
ROLLER'S Shark VE). Clean plastic parts (e.g. housing) only with machine
cleaner or a mild soap and a damp cloth. Do not use household cleaners. These
often contain chemicals which can damage the plastic parts. Never use petrol,
turpentine, thinner or similar products for cleaning.
Make sure that liquids never get inside the machine reciprocating saw. Never
immerse the machine reciprocating saw in liquid.
WARNING
Before any repair work, pull the mains plug! This work may only be performed
by qualified personnel.
The ROLLER'S reciprocating saws with universal motor have carbon brushes.
These are subject to wear and must therefore by checked and changed by
qualified specialists or an authorised ROLLER'S customer service workshop
from time to time.
eng