Technical Data; Scope Of Supply; Applications - Roller Fox ANC Notice D'utilisation

eng
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool's
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to
be performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
Safety instructions for ROLLER'S reciprocating saws
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
● Hold the power tool by the insulated handles ("A") when performing work
where the tool can come into contact with concealed electric cables or its
own power cable. Contact with a live cable can also put metal tools under voltage
and lead to electric shock.
● Hold the power tool tightly with both hands when working and make sure
you have a firm footing. The power tool can be controlled more safety with two
hands.
● Use personal safety equipment, e.g. protective glasses. Hot chips fly off to
all sides when sawing. Keep other persons away.
● Please note that health hazardous dusts could be produced when sawing.
Use suitable dust extractors, a respirator and disposable overalls if necessary.
Observe the national regulations.
● Use suitable finders to locate concealed supply lines or consult the local
supply company. Contact with electric cables can cause fires and electric shock.
Damage to a gas pipe can cause explosions. Penetration of a water pipe can
cause property damage or electric shock.
● Make sure when sawing pipes carrying water that no leaking water can get
into the motor. There is a danger of electric shock.
● Clamp the material tightly. Do not support the workpiece with your hand
or foot. There is a danger of injury.
● Secure the workpiece. It is safer to hold the workpiece with a clamping device
or vice than with your hand.
● Do not touch any objects or the ground with the running saw. There is a
danger of recoil.
● Keep your hands away from the sawing area. Do not reach underneath the
workpiece. Contact with the saw blade can cause injury
● Keep highly inflammable materials away from hot sawing chips during
sawing. There is a danger of fire!
● Make sure that the tiltable support shoe (6) is always in contact with the
workpiece when sawing. The saw blade can jam and lead to loss of control
over the power tool.
● When you have finished the work, switch off the power tool and do not
remove the saw blade from the cut until it has come to a standstill. This
avoids recoil and allows you to put down the power tool safely.
● Only use undamaged, flawless saw blades. Bent or blunt saw blades can
break or cause recoil.
● Do not slow down the saw blade after switching off by pressing against
the side. The saw blade could be damaged, break or cause recoil.
● Wait until the power tool has come to a standstill before you put it down.
The inserted tool can jam and lead to loss of control over the power tool.
● Pull out the mains plug or remove the battery before attaching/detaching
the saw blade. There is a danger of injury.
● Pull out the mains plug or remove the battery before adjusting the support
shoe. There is a danger of injury.
● Children and persons who, due to their physical, sensory or mental abilities
or lack of experience and knowledge are unable to operate the power tool
safely may not use this power tool without supervision or instruction by a
responsible person. Otherwise there is a risk of operating errors and injuries.
● Only allow trained persons to use the power tool. Apprentices may only use
the power tool when they are over 16, when this is necessary for their training
and when they are supervised by a trained operative.
● Check the power cable of the electric al device and extension leads regularly
for damage. Have these renewed by qualified experts or an authorised ROLLER
customer service workshop in case of damage.
● Only use approved and appropriate marked extension leads with a sufficient
cable cross­section at least with the protection class approved in 1.5.
Electrical data. Use extension leads up to a length of 10 m with cable cross-
section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm².
Explanation of symbols
WARNING
Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
CAUTION
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
10
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Use eye protection
Use a respirator
Use ear protection
Electrical device complies with protection class II
Environmentally friendly disposal
CE conformity mark
Force-transmitting
guide holder
90°
90°
Steel pipes
Metal
Stainless steel
Pallets
Wood
Wood with nails

1. Technical data

Use for the intended purpose
WARNING
ROLLER'S reciprocating saws are intended, using suitable saw blades, for sawing
different materials, e.g. steel pipes, stainless steel pipes, cast iron pipes, other metal
profiles, wood, wood with nails, pallets, building materials, plastics, also for plunge-
cut sawing in material that is not too hard.
All other uses are not for the intended purpose and are prohibited.
1.1. Scope of Supply
ROLLER'S Fox ANC/VE/SR: Drive machine, Allen key, guide holder up to 2",
2 ROLLER'S special saw blades up to 2"/140-3.2, sheet steel box, operating
instructions
ROLLER'S Shark VE: Drive machine, Allen key, 1 ROLLER'S saw blade
210-1.8/2.5, sheet steel box, operating instructions
ROLLER'S Carat ANC VE: Drive machine, Allen key, 1 ROLLER'S special saw
blade 150-1.8/2.5, sheet steel box, operating instructions
1.2. Article numbers
ROLLER'S Fox ANC drive unit
ROLLER'S Fox ANC VE drive unit
ROLLER'S Fox ANC SR drive unit
ROLLER'S Shark VE drive unit
ROLLER'S Carat ANC VE drive unit
Guide holder / " – 2"
1
16
Guide holder 2½" – 4"
Guide holder 5" – 6"
Double holder
Protective cap for guide holder, for clamping thin-walled material
Steel case

1.3. Applications

Right-angled sawing with ROLLER'S Fox ANC/VE/SR:
With guide holder 563000 and
ROLLER'S special saw blade 561001
Pipes (also plastic jacketed)
With guide holder 563100 and
ROLLER'S special saw blade 561002
Pipes (also plastic jacketed)
With guide holder 563200 and
ROLLER'S special saw blade 561008
Pipes (also plastic jacketed)
eng
Green wood
Breeze blocks
Plaster boards
Pumice, brick
Cast iron
corrugated
straight-set
straight
pellets
560000
560008
560001
560003
560006
563000
563100
563200
543100
563008
566051
/ " – 2"
1
16
2½" – 4"
5" – 6"