Connectivity Functions; Practical Advice; Maintenance And Service; Maintenance And Cleaning - Bosch GKS Professional 18V-68 GC Notice Originale

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 29

Connectivity functions

GKS 18V-68 GC
In conjunction with the Bluetooth® Low Energy Module
GCY 42, the following connectivity functions are available
for the power tool:
– Registration and personalisation
– Status check, output of warning messages
– General information and settings
– Management
– Setting the speed levels
The smartphone indicator (38) lights up if the power tool
sends information (e.g. a temperature warning) to a mobile
device via Bluetooth® wireless technology.
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 42.
GKS 18V-68 C
In conjunction with the Bluetooth® Low Energy Mod-
ule GCY 42, the following connectivity functions are avail-
able for the power tool:
– Registration and personalisation
– Status check, output of warning messages
– General information
– Management
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 42.

Practical advice

With the Bluetooth® Low Energy Module GCY 42, the
u
power tool is equipped with a radio interface. Local
operating restrictions, e.g. in aircraft or hospitals,
must be observed.
In areas where the Bluetooth® wireless technology is
u
not allowed to be used, the Bluetooth® Low Energy
Module GCY 42 and the button cell must be removed.
The width of cut varies depending on the saw blade used.
Protect saw blades against shock and impact.
Guide the power tool evenly, pushing it gently in the cutting
direction. Applying too much pressure to the power tool
when moving it in the cutting direction significantly reduces
the service life of the application tools and can damage the
power tool.
The sawing performance and the quality of the cut essen-
tially depend on the condition and the tooth shape of the
saw blade. This is why you should only use sharp saw blades
that are suitable for the material being machined.
Sawing wood
Choosing the right saw blade depends on the wood type,
wood quality and whether cuts with or against the grain are
required.
Making cuts in spruce with the grain produces long, spiral-
shaped chips.
Beech and oak dust is especially detrimental to health.
Therefore, work only with dust extraction.
Bosch Power Tools
Sawing with a parallel guide (see figure F)
The parallel guide (11) allows you to make precise cuts
along the edge of a workpiece and cut strips with the same
dimensions.
Slide the guide rod of the parallel guide (11) through the
guide into the base plate (13). Mount the parallel guide (11)
with the wing bolt (6).
Sawing with an auxiliary guide (see figure G)
For working on large workpieces or for cutting straight
edges, you can securely fasten a board or rail to the work-
piece as an auxiliary guide. The circular saw can be guided
along the path of this auxiliary guide with the base plate.
Sawing with the guide rail (see figures H – I)
GKS 18V-68 GC
You can use the guide rail (41) to produce straight cuts.
The adhesive layer prevents the guide rail from slipping and
preserves the surface of the workpiece. The guide rail's coat-
ing allows the power tool to glide more easily.
Place the circular saw directly on the guide rail (41). Fasten
the guide rail (41) to the workpiece using suitable clamping
devices, e.g. screw clamps, so that the narrow side of the
guide rail (41) is facing the saw blade.
The guide rail (41) must not protrude over the edge of
the workpiece being sawn into.
Switch on the power tool and push it gently in the cutting dir-
ection, guiding it evenly.
The connector (43) can be used to join two guide rails. The
four screws in the connector are used for the purpose of
clamping.
The groove (44) is suitable for guide rail systems from Bosch
and Mafell.
The groove (45) is suitable for guide rail systems from Fes-
tool and Makita.
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.

Maintenance and Service

Maintenance and Cleaning

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
English | 27
1 609 92A 5FB | (24.02.2020)

Publicité

Table des Matières
loading

Table des Matières