Illustrated Description; Operating Instructions; Placement And Testing - stayer CD125K Instructions D'emploi

Mount the elbow 11 ( optional)
10 and connect a vacuum hose 12 (accessory). Connect
the vacuum hose 12 with a vacuum cleaner (accessory). An
overview for the connection of various vacuum cleaners
can be found at the end of these instructions.
Mounting the Auxiliary Handle
Depending on the working manner, screw the auxiliary
handle 4 to the left on the auxiliary- handle holder.
Mounting Diamond Cutting Discs
When mounting and replacing diamond cutting
discs, it is recommended to wear protective
gloves.
Diamond cutting discs become very hot during
operation; do not touch them until they have
cooled down.
Place the power tool on its side so that the cutting-depth
scale 2 can be seen. Loosen clamping lever 9 and adjust
the least cutting depth.
Dismounting the Clamping Assembly (see figure A)
Loosen the knobs 9 and remove the protective cap 22.
Press the spindle lock button 7 to lock the grinding spindle.
Actuate the spindle lock button only when the
grinder spindle is at a standstill. Otherwise, the
machine may become damaged.
Loosen the clamping nut 19 with the two-pin spanner 20
and unscrew the clamping nut 19. Remove the spacer discs
18 and the mounting flange 16. Clean the grinder spindle 15
and all parts to be mounted.
Determining the Slot Width
The slot width results from the amount of spacer discs 18
between the two diamond cutting discs 17 (
and the cutting width of the diamond cutting discs.
The machine can be operated with one or two diamond
cutting discs.
Mounting the Clamping Assembly (see figure A)
Set the mounting flange 16 onto the grinder spindle 15. The
mounting flange with its driving feature must be properly
seated on the grinding spindle.
If the disc has rotational direction indication
(arrow) mount the disk so that the arrow on the
head 6 coincides with the arrow on the disc.
Place the diamond cutting disc 17 (
spacer discs 18 on the mounting flange 16.
Regardless of the requested slot width, all
spacer discs 18 provided must always be
mounted. Otherwise, the diamond cutting disc 17
( not included) can become loose during operation and lead
to injuries.
onto the vacuum connection
not included)
not included) and the
ENGLISH
21
Place the protective cover 22 and tighten the knobs 9.
At least one spacer disc 18 must be mounted between two
diamond cutting discs
When mounting the diamond cutting discs, ensure that the
direction-of-rotation arrows on the diamond cutting discs
match with the rotation rotation direction of the machine
(see direction of rotation arrow on the gear case).
Press the spindle lock button 7 to lock the grinding spindle.
Screw on the clamping nut 19 and tighten it with the two-pin
spanner 20.
When working with 2 diamond cutting discs
included), always replace them in pairs. See graphics page
for the mounting sequence.
The mounted diamond cutting discs 17 protrude
out of the protection guard, even at the least
preselected cutting depth. Therefore, never set
down the machine on the chaser rollers 3, but always
aside.

3.3 Illustrated description

1 On/Off switch
2 Cutting-depth scale
3 B acking roll
4 Auxiliary handle
5 Brush cover
6 Rotation indicator
7 Spindle lock button
8 Protection guard with cutting guide
9 Clamping lever for depth stop adjustment
10 Vacuum connection
11 Elbow*
12 Vacuum hose*
13 Service key
14 Screw lever for protection guard
15 Grinder spindle
16 Mounting flange
17 Diamond cutting disc*
18 Spacer discs
19 Clamping nut
20 Two-pin spanner for clamping nut*
21 Break-out tool*
22 Protective cover disk.
23 Safety button lock / unlock switch.
*
Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of accessories
can be found in our accessories program.

4. Operating instructions

4.1 Placement and testing

Observe correct mains voltage! The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Power tools marked with 230 V can also be operated
with 220 V.
Switching On and Off
Before starting the unit, place the unit on the
21
17 ( not included).
17 ( not