Publicité
Les langues disponibles
Les langues disponibles
FourChannelModels:
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Installation . . . as easy as 1, 2, 3
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the
top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4" (10cm) of open ventilation for
the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four
holes using a 7/64" (3mm) bit and use the supplied #8 screws to mount the amplifier.
2. Wiring Disconnect the vehicle's battery to avoid an electrical short. Then connect the ground wire
to the amplifier. Make the ground wire short, 24" (60cm) or less, and connect it to a paint-and
corrosion-free solid-metal area of the vehicle's chassis. Adding an additional ground wire between the
battery's negative post and the vehicle chassis
of this same gauge (or larger) is recommended.
Use a twisted pair(s) of RCA (low-level)
interconnect cable to feed the audio signal to
the amplifier. If you are using only one pair of
RCA inputs, connect the RCA cable to the AMP
1 inputs. Push the fader button out, and all four
channels will work with a single pair of RCA
input cable. Push the fader button in, when
using two pairs of RCA input cables. Keep the
RCA cable away from factory wiring harnesses
and other power wiring. If you need to cross this
wiring, cross it at a 90 degree angle.
Only use speaker wire (high-level) inputs if
your source unit does not have RCA type outputs. If you are using only one pair of high-level inputs,
connect the speaker wire to the AMP 1 input. Push the fader button out, and all four channels will work
with a single high-level input cable. Push the fader button in, when using both sets of high-level inputs.
Install a fuse within 18" (45cm) of the battery and in-line with the power cable connected to your
amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it.
See the chart below for power and ground wire size, and fusing recommendations.
3. Configuration The following
diagrams show the most common
configurations for your Kicker ZX series
amplifier.
TwoChannelOperation (Stereo) These ZX amplifiers are capable of operating into a minimum
impedance of 2 ohms per channel in stereo operation. See Figure 2.
BridgedOperation (Mono) ZX.4 series amplifiers are capable of operating into a minimum
impedance of 4 ohms when in bridged operation. See Figure 3.
StereoBridgedOperation (Simultaneously) The ZX.4 series amplifiers are capable of operating into a
minimum impedance of 4 ohms bridged and 2 ohms per channel in stereo operation. See Figure 4.
2
ZX.4SeriesAmplifier
Owner'sManual
ZX350.4 / ZX650.4 / ZX850.4
__________________________
Authorized Kicker Dealer:
__________________________
Purchase Date:
__________________________
Amplifier Model Number:
__________________________
Amplifier Serial Number:
Use only one type of signal input to the amplifier,
either RCA Cable or Speaker Wire
Speaker Wire
(High-Level
killers trk7"on Top"
Output)
RCA Cable
Fader Button: Push in for
(Low-Level)
2 pairs of inputs, push out
AMP 1
for a single pair of inputs.
HI-LEVEL
HI-LEVEL
1
2
INPUT
INPUT
+ - - +
+ - - +
FADER
AMP
1
L+
L-
R+
R-
Left
+
Speaker Wire
Left
-
(High-Level Input)
Right -
AMP 1
Right +
Left
Speaker Wire
Left
(High-Level Input)
Right -
AMP 2
Right +
ModelZX350.4
Fuse40A
PowerGroundWire 8GA
ModelZX650.4
Fuse80A
PowerGroundWire 4GA
ModelZX850.4
Fuse120A
PowerGroundWire 2GA
ZX.4AMPLIFIER
Ground
Remote
Turn-On
(45cm)
18"
Or Less
+12V
Battery
Figure 1
Ground
Remote
RCA Cable
Turn-On
(Low-Level)
Crossover
AMP 2
(45cm)
Switches
18"
Or Less
L
R
L
R
OFF HI LO
OFF HI LO
1
XOVER
XOVER
2
AMP 1 INPUT
AMP 2 INPUT
+12V
AMP
2
Battery
REMOTE BASS
L+
L-
R+
R-
+
-
Ground
Remote
Turn-On
(45cm)
18"
Or Less
+12V
Battery
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.
Minimum impedance of 2 ohms per channel in stereo operation
(60cm)
24"
Or Less
Fuse
Minimum impedance of 4 ohms when in bridged operation
(60cm)
24"
Or Less
Fuse
Minimum impedance of 4 ohms when in bridged operation
and 2 ohms per channel in stereo operation
(60cm)
24"
Or Less
Fuse
Right Speaker AMP 2
Left Speaker AMP 2
Figure 2
-
-
+
+
Signal In AMP 2
AMP2
Signal In AMP 1
AMP1
-
+
-
+
Left Speaker AMP 1
Right Speaker AMP 1
Figure 3
Mono Speaker AMP 2
-
+
Signal In AMP 2
AMP2
Signal In AMP 1
-
AMP1
+
Mono Speaker AMP 1
Figure 4
Mono Speaker AMP 2
-
+
Signal In AMP 2
AMP2
Signal In AMP 1
AMP1
-
-
+
+
Left Speaker AMP 1
Right Speaker AMP 1
3
Publicité
