BH FITNESS Columbia G-6490 K Instructions De Montage Et Utilisation page 12

appropriate wall socket, installed correctly and connected
to earth, in accordance with local regulations.
DANGER! If the equipment is not earthed correctly
then there is a risk of electrical shock. If in doubt, get an
electrician or technical specialist to check that the earth
connection is correct. Do not modify the plug supplied with
the equipment, if it does not fi t the wall socket then get an
electrician to install an electrical socket that does.
This product must only be used on a 220-240 volt circuit,
with an earthed socket similar to that shown in Figure
A. Make sure that the appliance is only connected to
a wall socket with the same pin layout as the plug. Do
not use an adaptor with this appliance.
Fig. A
Earth terminal
Socket with earth terminal
Always observe the following recommendations when
using electrical appliances:
1
Make sure that the mains supply voltage mat-
ches that of the machine before plugging it in. The
supply voltage must be the same as that stated on the
characteristics plate and the holes in wall socket must
match the pins for plug on the machine. Do not use any
type of adapter.
2
To reduce the risk of electrical shock, always unplug
the unit immediately after use and before proceeding
to clean it.
3
Only plug the machine into suitably earthed wall
sockets, as shown in Figure A. An inadequate electrical
connection may result in electrical shocks. If the plug is
not suitable for the wall socket then change it for one that
matches, bearing in mind that the earth wire must always
be connected. If in doubt, call BH technical services.
4
Never leave the unit unattended when it is plugged
in. Unplug it after use.
5
Do not allow children or the disabled to use the
appliance without the strict supervision of a qualifi ed
person.
6
Never use accessories not recommended by the
manufacturer.
7
Do not use the machine if the mains cable becomes
damaged or worn.
8
Keep the mains cable away from hot surfaces.
COLUMBIA G6490 K 0180125 12
9
Do not use the machine outdoors.
10
To unplug the machine, fi rst put the switch to the
"0" position and then unplug it from the wall socket.
SAFETY BREAKER
This model is equipped with an electronic circuit breaker
to protect both the electronic and electrical circuits.
This safety device will be automatically triggered if the
unit is subjected to abnormal force or heat.
Should this occur:
1.- Set switch (L), located on the casing, to the "0"
(OFF) position.
2.- Press the circuit button (C) to reset the unit.
3.- Next, set switch (L) to the "I" (ON) position and
the unit will be ready for use again.
Should the circuit breaker trip repeatedly then the most
probable causes are:
- Abnormal working conditions,
- Treadmill belt in need of lubricant,
- Solvent based lubricants used (use BH type),
- Belt is too tight.
Plug the unit into a wall socket with an EARTH terminal.
Set switch (L) to Position [1].
C
L
ASSEMBLY INSTRUCTIONS
Take the unit out of the box and place it on the fl oor as
shown in Figure 0. The assistance of a second person
is advisable for the assembly work. Make sure that all
of the pieces are there: (A) Monitor; (B) Main structure;
(C) side bar (left); (D) Side bar (right); (E) Side bar base
cover (Left); (F) Side bar base cover (Right); (G) left han-
drail (elevation); (H) right handrail (speed); (I) Handrail
cover (Left); (J) Handrail cover (Right); (S) Top trim, right
handrail; (T) Top trim, left handrail; (K) Bottle; (a) Allen
screw M5x10; (b) Allen screw M8x15; (c) Allen screw
M8x60; (d) Self-tapping screw 5x25; (e) Allen key 5 mm;
(f) Allen key 6 mm; (g) Safety key; (h) Mains cable; (i)
Bottle of lubricant.
Follow the instructions step by step to assemble:
12
11/4/05, 16:59