Denon CDR-1000 Mode D'emploi page 17

NOTES:
• If there are no discs in the memory, the message
"MEMORY EMPTY" appears on the display.
• It is not possible to check or erase the text of a disc
that has been finalized. When the disc is finalized, the
text stored in the memory of this unit is moved to the
disc.
• When the text memory of your CD recorder is full, the
message "MEMORY FULL" will appear, followed by
"FINALIZE CD". If you want to add a CD to the list of
discs for which text is stored, you have to erase a disc
from this list or finalize another disc. ("for which text is
stored")
• "MEMORY FULL/FINALIZE CD" may also appear when
unfinalizing a CD-RW disc for which text was stored
(see 'Unfinalizing CD-RW discs'). The same action(s)
should be taken in order to obtain memory space.
Recording Settings
The recording setting mode permits the setting of fade
recording, the auto track function, and recording balance.
Details of the recording settings are stored in this unit. The
next time a recording is made, it can be made with the
same settings. To use different settings, change those
settings when required.
Note that settings details are not stored only for the
recording balance setting mode. Make settings as required.
SET FADE
Fade
This unit permits fade-in recording, where the recording
level gradually increases from the start of the recording, as
well as fade-out recording, where the recording level
gradually decreases from the where the STOP button (
was pressed and the recording ends, or from where the
PLAY/PAUSE button ( / ) or the PAUSE button ( ) on the
1 3 3
remote control was pressed and the recording was paused.
9
B CDR-1000 PLAY /PAUSE STOP REC MODE
PCM AUDIO TECHNOLOGY/ CD RECORDER OPEN /CLOSE
STANDBY REM REC TIME TRACK TIME
/
1 2 3 4 5 6 7 8 9 10 11
L
OPTICAL I CD RW R MANUAL SYNC REPEAT
REMOTE SENSOR
STORE/
PHONES PHONES LEVEL DISPLAY INPUT SHUFFLE MENU
¢ ON / STANDBY £ OFF
-
SCROLL CANCEL / DELETE
ERASE FINALIZE
MIN MAX
1,8
ON /STANDBY
SCAN
REPEAT PROGRAM SHUFFLE
ABC DEF GHI
1 2 3
JKL MN OPQ
4 5 6
RST UVW XYZ
7 8 9
TRACK MARK SPACE SCROLL
0
PLAY
STOP
PAUSE
8
STORE / CANCEL/
MENU ENTER DELETE
1,8
2,4,6
REMOTE CONTROL UNIT RC-276
1 Select the SET FADE submenu.
• "SET FADE" appears on the display.
2 Press the ENTER button to confirm.
• "FADE ON/OFF" appears on the display.
3
Press the ENTER button and turn the MULTI JOG dial to
select " ON " or " OFF ".
4 Press the ENTER button to confirm.
• "FADE ON/OFF" appears on the display again.
Turn the MULTI JOG dial to select "SET FADE IN" or
5
"SET FADE OUT".
6 Press the ENTER button to confirm.
• The currently set fade time is displayed.
7 By turning the MULTI JOG dial you can set the FADE IN
or FADE OUT time.
• The fade time can be adjusted from 0 to 10 seconds in
0.05 second increments. It will be displayed in the
form of "0 MS ~ 0000 MS".
• FADE IN automatically starts when you press RECORD
to start recording. Your recording will automatically be
faded out when you press the STOP button (
PLAY/PAUSE button ( / ) or the PAUSE button (
1 3
the remote control.
8 Press the STORE/MENU button to store settings and
)
2
return to the submenu or STOP button (
NOTES:
• Fade-in and Fade-out will not function in Synchro-
recording mode. However, the sound fades out if the
STOP button ( ) or the PAUSE button (
2
REC
during synchronized recording.
PROGRAM
• Use manual recording when performing fade-in
MULTI JOG
+
recording.
ENTER
1~7
AUTO TRACK
Auto track increment
The auto track function setting can be switched in the
manual recording mode. It is also possible to give track
numbers manually as you record.
The operation conditions of the auto track function will differ
depending on the input source. For details, see "Track
Numbers" on Page 6.
The set mode is stored and this allows the set information
to also be used the next time a recording is made.
B PCM AUDIO TECHNOLOGY/ CD RECORDER CDR-1000 OPEN /CLOSE
STANDBY REM REC TIME TRACK TIME
1 2 3 4 5 6 7 8 9 10 11
L MANUAL SYNC
OPTICAL I CD RW R
REMOTE SENSOR
PHONES PHONES LEVEL
¢ ON / STANDBY £ OFF
MIN MAX
ON /STANDBY
SCAN
REPEAT PROGRAM SHUFFLE
ABC DEF GHI
1 2 3
JKL MN OPQ
4 5 6
RST UVW XYZ
7 8 9
TRACK MARK SPACE SCROLL
1
0
PLAY
STOP
PAUSE
STORE / CANCEL/
MENU ENTER DELETE
1,5
2,4
REMOTE CONTROL UNIT RC-276
1 Select the AUTO TRACK submenu.
• "AUTO TRACK" appears on the display.
2
Press the ENTER button to confirm.
3
Select the Auto track "ON" or "OFF".
4 Press the ENTER button to confirm.
• When "ON" is selected, track numbers will be
) or the automatically incremented during recording.
2
) on • When "OFF" is selected, you can number the recorded
3
tracks yourself. (Press the TRACK MARK button on the
remote control.)
) to exit.
2 5 Press the STORE/MENU button to store settings and
return to the submenu or STOP button (
NOTES:
• In the Autostart recording mode, the track number
) is pressed
3 cannot be associated manually.
• In the Autostart recording mode, the auto track function
is automatically activated regardless of whether the
auto track mode is set ON or OFF.
• The track number cannot be changed after the
recording.
• The track number cannot be changed for 4 seconds
following the last change. (See "Restrictions in
Recording with this Unit" on Page 7.)
5
PLAY /PAUSE STOP REC MODE REC
/
REPEAT PROGRAM
STORE/
DISPLAY INPUT SHUFFLE MENU MULTI JOG
- +
SCROLL CANCEL / DELETE
ERASE FINALIZE
ENTER
1,5 1~4
ENGLISH
) to exit.
2
17