Important - POWER SMITH PWLD200T Notice D'utilisation

PRODUCT OVERVIEW
See FIG 1
1.
Carrying Handle
2.
Work Light Heads
3.
Lens
4.
Side Locking Knobs
5.
On/Off Switch
UNPACKING CONTENTS

Important!

Due to modern mass production
techniques, it is unlikely the product is faulty or that a part
is missing. If you find anything wrong, do not operate the
tool until the parts have been replaced or the fault has been
rectified. Failure to do so could result in serious personal
injury.
contents In packaGe
Description
Work Light Heads
Stand With Carrying Handle
Tripod
Manual
SPECIFICATIONS
Rated Power ...........................120 V~, 60Hz, 170W
Brightness ..............................20,000 Lumens
Color Temperature ..................5000K Bright White
CRI .........................................>80
Cord ....................................... 9 ft. 18/3 SJTW
Tripod Height ......................... 30" - 65"
Net Weight ............................. 13.1 lb
SYMBOLOGY
SYM- DESCRIP- SYM-
BOL TION BOL
V
Voltage
A
Amperes
Hz
Hertz
W
Watts
LM
Lumens
English
6.
LEDs
7.
H-Stand
8.
Tripod
9.
Power Cord
Quantity
2
1
1
1
DESCRIPTION
Alternating current
Symbol of safety warning
and precautions
Read operator's manual
No dumping with house-
hold Waste
ETL listing for U.S. and
Canada
IMPORTANT SAFETY INSTRUCTIONS
READ AND UNDERSTAND ALL WARNINGS, CAUTIONS
AND OPERATING INSTRUCTIONS BEFORE USING THIS
EQUIPMENT. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious personal
injury.
WaRnInG:
not use with an extension cord near water or where water
may accumulate. Keep work light at least 16 feet from
pools and spas. Keep plugs and receptacles dry. Use only
three-wire outdoor extension cords with grounded plugs
and grounded receptacles.
•
Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be
used for this light in wet locations. Receptacles are
available having the built-in GFCI protection and are able
to be used for this measure of safety.
•
Use only with an extension cord for outdoor use,
such as an extension cord of cord type: SW, SW-A, SOW,
SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A,
SJOW, SJOW-A, SJTW, SJTW-A, or SJTOW, SJTOW-A.
•
Do not look directly at the lighted lamps to avoid eye
injuries.
•
Always keep the work light away from any
flammable surface or materials.
•
Always check damaged or worn-out parts before
using the work light. Broken parts will affect the work
light operation. Replace or repair damaged or worn
parts immediately. If repairs are needed, consult a
professional electrician.
•
Do not use a pressure washer to clean this product.
•
Do not modify the work light in any way. Unauthorized
modification may impair the function and/or safety and
could affect the life of the product. There are specific
applications for which the work light was designed.
•
Store work light in a secure place out of the reach of
children. Inspect it for good working condition prior to
storage and before re-use.
ASSEMBLY INSTRUCTIONS
attacHInG WoRk LIGHt HeaDs to
stanD (FIG 2)
1.
Place the stand (7) on a flat surface.
2.
Rotate the carrying handle (1) straight up. Tighten the
handle locking knob (G3) to secure it in place.
3.
Install one work light head (2) on the stand (7) by sliding
and positioning the U-shape bracket (10) under the bolt
cap (G2) as shown in FIG 2. Tighten the locking knob
(G1) to secure the work light head in place. Repeat the
procedure on the second work light head.
4.
Hang the power cable splitter (H) on the hook (G4).
3
RISK OF ELECTRIC SHOCK, Do