Your Product; Safety Information; Wall Mounting - Staba Litho Mode D'emploi

Generally
This appliance is for private use only and must not be used commercially. Please read
the instruction manual carefully and keep it at a safe place. When the appliance is
given to another person the instruction manual should be passed to that person, too.
Only use the appliance as described in the instruction manual and pay attention to
the safety information. No liability for damages or accidents will be accepted, which
are caused by not paying attention to the instruction manual.

Your product

Other than the heater you have chosen the package includes (picture 1):
- N° 2 plastic brackets for wall mounting;
- N° 4 rawplugs 6x25mm;
- N° 4 3,5x55mm cross head screws to fix wall brackets;
- N° 1 drill pattern for wall mounting.
Refer to your dealer is something is broken or missing.

Safety information:

∙ Connect and operate the appliance only in accordance with the specifications on
the rating label.
∙ Do not use if the power cord is damaged. This must be checked before each use.
∙ This appliance is not intended for use by persons (including children)
with reduced physical, sensory, or mental capacities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety
∙ Children should be supervised to ensure that they do not play with the appliance.
∙ The appliance is not intended to be operated by means of an external timer or
separate remote control system.
∙ After each use or in the case of a malfunction the plug must be pulled out of the
socket.
∙ Never pull at the power cord. Do not chafe it over sharp edges or squeeze it.
CAUTION
∙ — Some parts of this product can become very hot and cause
burns. Particular attention has to be given where children and vulnerable
people are present.
∙ Make sure that your supply rating corresponds to what specified on the rat-
ing plate: 230V~, 50Hz.
∙ The product has a double IP protection level against water: IPX1 when
portable and IPX4 when wall mounted (picture 2). Respect your country
regulations about the use of the product in different environments.
∙ Don't leave your home while the appliance is in function: ensure in this case that
the switch is in OFF (0) position and the thermostat is in minimum position ().
∙ During function, place the heater in a safe position:
- at least 1m far from inflammable objects or furnitures;
- leaving not less than 1m of free space in front of the heater;
10
- not located immediately below a socket-outlet.
∙ Do not leave animals or children touch or play with the appliance. Pay attention!
The air outlet grille gets hot during operation (more than 90°C)
∙ WARNING: In order to avoid overheating, do not cover the heater.
Do not hang anything on the heater and do not cover it while it's wor-
king. This is clearly written on the cover of the product or shown by the
symbol
∙ Do not use the heater in rooms with explosive gas or while using inflammable
solvents or varnish or glues.
∙ If the cordset is damaged and you have to change it, do not do the job yourselves!
Take the product to an after sales authorised repair centre or to a person with simi-
WARNING: In order to avoid overheating, do not cover the heater. Do not hang anything on
the heater and do not cover it while it's working. This is clearly written on the cover of the product
lar skill and knowledge, in order to avoid any risk of danger.
or shown by the symbol
∙ When portable, do not use this heater close to showers, baths, swimming pools.
∙ The appliance must be positioned so that the plug is always accessible.
∙ Do not mount the product on walls made of synthetic material.
Do not use the heater in rooms with explosive gas or while using inflammable solvents or varnish

Wall mounting

or glues.
If the cordset is damaged and you have to change it, do not do the job yourselves! Take the
∙ Only fix the heater in vertical position with the air outlet grid downword;
product to an after sales authorised repair centre or to a person with similar skill and knowledge,
in order to avoid any risk of danger.
∙ This heater is fitted with a double electrical insulation circuit (class II) and therefore
When portable, do not use this heater close to showers, baths, swimming pools.
does not require an earth connection.
The appliance must be positioned so that the plug is always accessible.
∙ When wall mounted, the heater is water resistant to IPX4. It can therefore be used
Do not mount the product on walls made of synthetic material.
in bathrooms or other areas subject to humidity as long as it is not installed within
3. Wall mounting
the perimeter of bath tubs or showers. This means that it cannot be installed in the
areas marked as VOLUME 1 in figure 1.
Only fix the heater in vertical position with the air outlet grid downword;
∙ It must never be possible for people in the bath tub or shower to reach the adjust-
This heater is fitted with a double electrical insulation circuit (class II) and therefore does not
ment knobs.
require an earth connection.
When wall mounted, the heater is water resistant to IPX4. It can therefore be used in bathrooms
∙ This heater must be correctly installed in compliance with the regulations in force in
or other areas subject to humidity as long as it is not installed within the perimeter of bath tubs or
the country of installation.
showers. This means that it cannot be installed in the areas marked as VOLUME 1 in figure 1.
∙ IMPORTANT FOR FRANCE: It must never be possible for people in the bath tub or shower to reach the adjustment knobs.
This heater must be correctly installed in compliance with the regulations in force in the country of
If the product is to be wall mounted the electrical connection to the power supply
installation.
must be done by cutting off the plug supplied and using a suitable terminal as per
IMPORTANT FOR FRANCE:
the diagram shown below:
If the product is to be wall mounted the electrical connection to the power supply must be done
by cutting off the plug supplied and using a suitable terminal as per the diagram shown below:
L
Net
N
In wet spaces like bathrooms or kitchens, the connection terminal must be installed at least 25
∙ In wet spaces like bathrooms or kitchens, the connection terminal must be installed
cm above the floor. The electrical connection to the power supply must also be fitted with a two-
pole switch with a minimum gap between the contacts that allows complete disconnection
at least 25 cm above the floor. The electrical connection to the power supply must
according to excess voltage III category conditions.
also be fitted with a two-pole switch with a minimum gap between the contacts
that allows complete disconnection according to excess voltage III category condi-
Mount the heater on the wall making sure to observe the minimum distances from the ceiling,
floor and other walls, as shown in picture 4;
tions.
To proceed with the installation:
∙ Mount the heater on the wall making sure to observe the minimum distances from
Drill four 6 mm diameter holes in the wall, as shown in picture 5. A drill pattern is provided to
the ceiling, floor and other walls, as shown in picture 4;
help you marking the correct position of the holes;
Insert the four wall plugs supplied with the product;
∙ To proceed with the installation:
Fix the upper and the lower brackets as shown in picture 6;
Hang the product to the upper bracket and then hook it up to the lower bracket untill you ear a
"click" as shown in picture 7.
Phase = brown
Product cable
Neutral = blue
11