Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Installation
General
The table lists the correct cable connections.
Mounting the Scanner
This scanner is designed to operate indoors only and can support a max. load of 15.41lbs
(=7kg). In order to perform adequately, the device should be securely fastened to a suitable
mounting surface. The camera should be correctly mounted and balanced on the scanner. The
round-based scanner is installed directly on the mounting bracket. Tighten the scanner's
mounting screws just enough so that the base is effectively immobilised.
CAUTION : Do not attach the unit to a drywall. Attach the scanner to the mounting bracket
using a hex-head screw equipped with a locknut or use our camera mounting
bracket (CAMB7 or CAMB8).
Number
Connection
1
2
3
4
COMMON
Note that the "LEFT" and "RIGHT" connections are inverted with inverted mounting of the
device.
Inverted Mounting of the Unit
The left-right directions for manual operation are reversed with inverted mounting of the device.
Correct the wiring accordingly when connecting the control unit with the scanner : the cores
connected to pin 2 and pin 3 at the back of the central unit should be switched. Consult figures
"2c" and "2d" at the back of the manual for inverted mounting of the scanner and the camera.
Connecting the Scanner to the Central Unit
The power cable of the scanner can be connected to the connections at the back of the central
unit (the scanner uses a 24VAC power supply) for independent and automatic operation.
Connect the cores of the cable as shown in the table (see above).
Installing the Limit Stops
The toothed wheel is slotted at intervals of 5°. The coiled (extension) cord with BNC connector
is connected to the rear of the scanner. The reversing switch activator (1 in fig. 1 at the back of
the manual) is visible between the toothed wheel and the housing on the front side of the unit.
VIS1
VIS1 – CCTV INDOOR SCANNER
Normal Mounting
24VAC
LEFT
RIGHT
GREEN or
Colour
Connection
RED
WHITE
YELLOW
BLACK
1
Inverted Mounting
24VAC
RIGHT
LEFT
COMMON
Colour
RED
GREEN or
YELLOW
WHITE
BLACK
VELLEMAN
Publicité
Manuels Connexes pour Velleman VIS1
Sommaire des Matières pour Velleman VIS1
- Page 1 VIS1 – CCTV INDOOR SCANNER Installation General The table lists the correct cable connections. Mounting the Scanner This scanner is designed to operate indoors only and can support a max. load of 15.41lbs (=7kg). In order to perform adequately, the device should be securely fastened to a suitable mounting surface.
- Page 2 Loosen the hex-head screws (4 in fig. 1) with locknut on the side of the mounting bracket to adjust the angle of the camera. Retighten the two screws firmly when the desired angle has been obtained. VIS1 VELLEMAN...
- Page 3 VIS1 – CCTV INDOOR SCANNER Installatie Algemeen De tabel vermeldt de correcte kabelaansluitingen. Montage van de scanner Deze scanner mag enkel binnenshuis worden gebruikt en kan werken met een max. belasting van 7kg. Het toestel werkt naar behoren indien het is bevestigd aan een geschikt bevestigingsoppervlak.
- Page 4 : de iris compenseert immers voortdurend de veranderende lichtintensiteit. Gebruik een schroef met een borgmoer om de camera te bevestigen. U kunt deze schroef op 3 verschillende plaatsen aanbrengen (zie 5 in fig. 1) naargelang van het evenwicht dat u bekomt. VIS1 VELLEMAN...
-
Page 5: Vis1 - Scanner Cctv Pour Usage A L'interieur
Les directions "LEFT" (gauche) et "RIGHT" (droite) pour l'opération manuelle de l'appareil seront inversées lors du montage inversé du VIS1. En ce cas, il faudra donc également changer le câblage qui lie le scanner et l'unité centrale : les brins pour les bornes de connexion 2 et 3 à... - Page 6 Utilisez une vis équipée d'un contre-écrou pour fixer la caméra sur le support de montage, qui est pourvu de trois trous de montage. Choisissez le trou qui donne le plus d'équilibre à la caméra (voir 5 de la fig. 1). VIS1 VELLEMAN...
-
Page 7: Mounting The Camera
MOUNTING THE CAMERA FIG. 2a : normal upright mounting normale montage rechtop montage normal droit 10° up angle = opwaartse hoek 10° = angle ascendant de 10° 90° down angle = benedenwaartse hoek 90° = angle descendant de 90° VIS1 VELLEMAN... - Page 8 = voorkant van de scanner = 10° up angle = devant du scanner opwaartse hoek 10° = angle ascendant de 10° 90° down angle = benedenwaartse hoek 90° = angle descendant de 90° VIS1 VELLEMAN...
- Page 9 > 10° omgekeerde montage, opwaartse hoek > 10° montage inversé, angle ascendant > 10° 90° up angle = opwaarste hoek 90° = angle ascendant de 90° 10° down angle = benedenwaartse hoek 10° = angle descendant de 10° VIS1 VELLEMAN...