Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

1. Introduction
Thank you for buying the VDP150SC4! Read this manual carefully before bringing the device into service.
Make sure that the device was not damaged in transit. If it was, don't install the device and contact your dealer.
2. Safety Instructions
- Everyone involved with the installation, operation and maintenance of this device has to be qualified and follow the
instructions of this manual meticulously.
- Be very careful during installation: touching high voltage live wires can cause life-threatening electric shock.
- Damage caused by disregarding certain guidelines in this manual voids the warranty.
- Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device
against damage by leaving it switched off until it has reached room temperature.
- This device falls under protection class I. Therefore it is essential that the device be earthed.
- Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
- Do not crimp the power cord and protect it against damage from sharp edges.
- Always disconnect the device from the mains when it is not in use or when you wish to clean it. Only handle the
power cord by the plug. Never pull out the plug by tugging the power cord.
- Do not look directly into the light source as sensitive people may go into epileptic seizure if they do.
- There may be some smoke or a particular smell when the device is activated for the first time. This is normal and
any smoke or smell will gradually disappear.
- Never touch the device during operation as the housing heats up and contact may cause burns.
- Note that damage caused by user modifications to the device is not covered by the warranty. Keep the device
away from children and unauthorised users.
3. General Guidelines
- This device is a light controller for professional use on stages, in discos, theatres, etc. It should only be operated
with an alternating current of 230V AC/50Hz. This device is designed for indoor use only.
- Lighting effects are not designed for permanent operation : regular operation breaks will make them last longer.
- Do not shake the device. Avoid brute force when installing or operating the device.
- Select a location where the device will be protected against extreme heat, moisture and dust. Respect a minimum
distance of 50cm between the projector and the illuminated surface.
- Always secure the device with an appropriate safety cable (VDLSC7 or VDLSC8).
- Familiarise yourself with the functions of the device before actually using it. Do not permit operation by unqualified
people. Any damage that may occur will probably be caused by unprofessional use of the device.
- Use the original packaging if the device is to be transported.
- Note that all modifications of the device are forbidden for safety reasons.
- Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electric shock, lamp
explosion, crash, etc. Using the device in an unauthorised way will void the warranty and may damage the device.
4. Installation
a) The Lamp
- Disconnect the unit from the mains to install or replace the lamp.
- Replace the lamp immediately if it's damaged or deformed.
- Let the lamp cool down before replacing it, for it can heat up to 700°C.
VDP150SC4 v2
VDP150SC4 -- DMX SCANNER
1
VELLEMAN

Publicité

loading

Sommaire des Matières pour Velleman VDP150SC4

  • Page 1 VDP150SC4 -- DMX SCANNER 1. Introduction Thank you for buying the VDP150SC4! Read this manual carefully before bringing the device into service. Make sure that the device was not damaged in transit. If it was, don’t install the device and contact your dealer.
  • Page 2 The DMX start address of the controller is defined by the 9 DIP switches. Since this device has 4 channels, the following settings should be applied when chaining them together: projector 1 = address 1, proj. 2 = address 5, proj. 3 = address 9 etc. VDP150SC4 v2 VELLEMAN...
  • Page 3 120ohm (1/4W) resistor between pin 2 and 3. You can make this yourself using a male XLR connector. The unit is controlled by 4 channels: CHANNEL 1: select one of the 8 colours or lamp off CHANNEL 2: select one of the 12 gobos CHANNEL 3: PAN (0-150°) CHANNEL 4: rotation speed & direction VDP150SC4 v2 VELLEMAN...
  • Page 4 460 x 220 x 110mm Total Weight 9.4kg Lamp 1 x 15V / 150W, GZ6.35 socket (LAMP150/15) Maximum Ambient Temperature T 45°C Maximum Housing Temperature T 130°C The information in this manual is subject to change without prior notice. VDP150SC4 v2 VELLEMAN...
  • Page 5 1. Inleiding Dank u voor uw aankoop! Lees de handleiding van uw VDP150SC4 aandachtig voor u het toestel in gebruik neemt. Ga na of het toestel werd beschadigd tijdens het transport. Zo ja, installeer het toestel niet en raadpleeg uw dealer.
  • Page 6 Dit toestel heeft 4 kanalen ; daarom moet u deze instellingen gebruiken als u ze aan elkaar koppelt: projector 1 = adres 1, projector 2 = adres 5, proj. 3 = adres 9 etc. Voor een overzicht van de instellingen, zie de figuur bovenaan pagina 3. VDP150SC4 v2 VELLEMAN...
  • Page 7 460 x 220 x 110mm Totaal gewicht 9.4kg Lamp 1 x 15V / 150W, GZ6.35 fitting (LAMP150/15) Maximum omgevingstemperatuur T 45°C Maximum behuizingtemperatuur T 130°C De informatie in deze handleiding kan te allen tijde worden gewijzigd zonder voorafgaande kennisgeving. VDP150SC4 v2 VELLEMAN...
  • Page 8 - Transportez l'appareil dans son emballage originel. - Toute modification de l’appareil est interdite pour des raisons de sécurité. - N’utilisez votre VDP150SC4 qu’à sa fonction prévue. Tout autre usage peut causer des courts-circuits, des brûlures, des électrochocs etc. Un usage impropre annule d'office la garantie.
  • Page 9 Cet appareil a 4 canaux; c’est pourquoi vous devez utiliser ces réglages quand vous les attachez: projecteur 1 = adresse 1, projecteur 2 = adresse 5, projecteur 3 = adresse 9 etc. Vous trouverez un aperçu des réglages en haut de la page 3. VDP150SC4 v2 VELLEMAN...
  • Page 10 Dimensions 460 x 220 x 110mm Poids total 9.4kg Ampoule 1 x 15V / 150W, culot GZ6.35 (LAMP150/15) Température ambiante max. 45°C Température boîtier max. 130°C Les informations dans ce manuel peuvent être modifiées sans notification préalable. VDP150SC4 v2 VELLEMAN...
  • Page 11 VDP150SC4 – DMX-SCANNER 1. Einführung Danke für den Kauf des VDP150SC4! Lesen Sie diese Bedienungsanleitung sorgfältig durch. Überprüfen Sie, ob Transportschäden vorliegen. Sollte dies der Fall sein, verwenden Sie das Gerät nicht und wenden Sie sich an Ihren Händler. 2. Sicherheitsvorschriften - Jeder Beteiligte an der Installation, Wartung und am Betrieb dieses Gerätes muss qualifiziert sein und die...
  • Page 12 - Stehen Sie während der Montage, Entfernung oder Wartung nie direkt unter dem Gerät. Lassen Sie das VDP150SC4 jährlich und vor der Inbetriebnahme von einem Fachmann prüfen. - Montieren Sie das Gerät an einem Ort, an dem es wenig Vorübergehende gibt und der unzugänglich ist für Unbefugte.
  • Page 13 5. Verwenden Sie zur Reinigung ein feuchtes Tuch. Verwenden Sie auf keinen Fall Alkohol oder irgendwelche Lösungsmittel. 6. Die Teile dürfen nicht eigenmächtig ersetzt werden (außer der Lampe und Sicherung) (siehe "4. Installation" S. 12). 7. Bestellen Sie eventuelle Ersatzteile bei Ihrem Fachhändler. VDP150SC4 v2 VELLEMAN...
  • Page 14 230V AC, 50Hz Stromverbrauch maximal 170W Sicherung F 2A, 250V AC (5x20mm) (Artikelnummer FF2) Abmessungen 460 x 220 x 110mm Gesamtgewicht 9.4kg Lampe 1 x 15V / 150W, GZ6.35-Fassung (LAMP150/15) Max. Umgebungstemperatur 45°C Max. Gehäusetemperatur 130°C Alle Änderungen vorbehalten. VDP150SC4 v2 VELLEMAN...