Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
INSTRUCTION ON MOUNTING AND USE
GB
Installation
The cooker hood must be placed at a minimum distance of
50 cm from the cooking plane for electric cookers and 65cm
for gas or mixed cookers.
The hood is equipped with a top air outlet
discharge of fumes to the outside (
exhaust pipe and pipe fixing clamps not provided).
Should it not be possible to discharge cooking fumes and vapour to
the outside, the hood can be used in the
activated carbon filter (in the case of the model with two suction
motors then two active carbon filters are required), a discharge tube,
for the expulsion of fumes, should be mounted on the connection ring
C
(Fig. 7) situated on the top of the wall cabinet (discharge tube and
fixing brackets are not supplied).
The models with no suction motor only operate in ducting mode, and
must be connected to an external suction device (not supplied).
Preliminary information for installation of the hood:
Disconnect the hood during electrical connection, by turning the
home mains switch off.
1.
D
Fix the 2 brackets
(Fig. 1) to the side panel of the wall cabinet
(one per side) with 2 screws for each bracket (align the bracket
to lower border).
Position the bracket to touch the back border of the wall
cabinet, considering that the back border of the bracket
corresponds to the back side of the cooker hood;
If the cooker hood is provided with a spacer, in case of
use, move the bracket forward to the same thickness
as the spacer.
Drill a hole on the ceiling of the wall cabinet to pass the
discharge tube and the electrical cable (the quote
indicated in Fig. 1 does not include the eventual spacer).
2 .
E
Fix 2 brackets
(Fig. 2) to the sides of the cooker hood
(one per side).
a. remove the extractable part of the cooker hood;
b. remove the grease filter/s;
c. fix the brackets with two screws
inside the cooker hood, affix them as more as possible
upwards (air exit side) and then serrate the screws.
3 .
Q
Fix the aesthetic mask
hood using two screws, (if supplied - Fig. 3 – the
present on the body of the cooker hood serve as further
fixing for the mask and should be visible once the mask
has been fitted) and then finally affix the spacer
three Clips from the external part of the cooker hood (if
supplied - Fig. 4).
4 .
Insert the cooker hood in the wall cabinet, ensuring to
position the cooker hood bracket
D
cabinet bracket
(Fig. 5).
Thread the electric cable through the appropriate perforation.
5.
Block the cooker hood with two screws on the frontal part (Fig.
5 – one per side).
Consult the designs in the front pages referenced in the text by alphabet letters.
for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined.
B
(Fig. 2) for
Ducting version
–
filter version
, fitting an
P
per bracket from
from the inside of the cooker
L
tabs
M
with
E
above the wall
6 .
Connect the cable to the electrical mains, only when the
installation is completed.
7 .
If the cooker hood should not touch perfectly with the
lower border of the wall cabinet then regulate by
P
loosening the screws
the cooker hood (Fig. 2), it will be possible to regulate
the perfect matching of the cooker hood and wall cabinet,
once regulated tighten the screws.
8 .
Regulate the gliding of the extractable drawer in relation
to the depth of the wall cabinet by acting on the two skirting
F
boards
(Fig. 6).
In this way it will be possible to place the front in line with
the wall cabinet (Fig. 6).
a. Loosen the screws on the skirting board
b. Move the ledges backwards or forwards depending on
requirement.
c. Lock in the screws on the ledges.
9 .
Install a discharge tube on the connection ring
preferably with a diameter equivalent to the connection
ring (Fig. 7). the discharge tube should be sufficiently
long to reach outside (Suction version) or the ceiling of
the wall cabinet (Filter version).
10.
Fix the connection ring
exit of the cooker hood.
To ease the installation, the ring is equipped with an index
should correspond to the appropriate guide
upper air exit.
11.
Complete the installation of the discharge tube.
12.
Re-install the grease filters, connect the cooker hood to
the electrical mains and check the perfect operation.
Electrical connection
The electrical tension must correspond to the tension noted on the
label placed inside the cooker hood. Connect the electrical plug,
where provided, to the an easily accessible outlet in conformity with
local standards in force.
Where an electrical plug is not provided (for direct connection to
electrical network) place a standards approved bipolar switch with
an aperture distance of not less than 3mm (accessible) from the
contacts.
Closely follow the instructions set out in this manual.
E
of the brackets
mounted on
F
;
C
supplied,
C
(snap into place), at the upper
G
that
H
placed on the
All responsibility,
Publicité
Table des Matières
