Pioneer DJM-900SRT Serato DJ Edition Mode D'emploi page 20

The cycle at which the cut-off frequency is moved fluctuates
X-PAD (parameter 4)
finely.
FLANGER 1
A 1-cycle flanger effect is produced according to the beat fraction set with the [BEAT
, ] buttons.
Short delay
Cycle
Use these to set the 1/4 – 64/1 effect time with respect to the
, buttons (parameter 1)
BEAT
time of one beat of the BPM.
Use this to set the cycle by which the flanger effect moves.
TIME control (parameter 2)
10 to 32000 (ms)
The further the control is turned clockwise, the more the effect
LEVEL/DEPTH control (param- is stressed.
eter 3) When turned all the way counterclockwise, only the original
sound is output.
X-PAD (parameter 4) The cycle at which the flanger effect is moved fluctuates finely.
PHASER
1
The phaser effect changes according to the beat fraction set with the [BEAT
buttons.
Phase shift
Cycle
Use these to set the cycle for moving the phaser effect as of
, buttons (parameter 1) time of 1/4 – 64/1 with respect to the time of one beat of the
BEAT
BPM.
This sets the cycle by which the phaser effect is moved.
TIME control (parameter 2)
10 to 32000 (ms)
The further the control is turned clockwise, the more the effect
LEVEL/DEPTH control (param- is stressed.
eter 3) When turned all the way counterclockwise, only the original
sound is output.
X-PAD (parameter 4) The cycle at which the phaser effect is moved fluctuates finely.
ROBOT
1
The original sound is changed to a sound like one produced by a robot.
Use this to set the degree of the effect sound.
, buttons (parameter 1)
BEAT
-100–100 (%)
Use this to set the degree of the effect sound.
TIME control (parameter 2)
-100–100 (%)
LEVEL/DEPTH control (param- Sets the balance between the original sound and the effect
eter 3) sound.
X-PAD (parameter 4) This changes the degree of the effect sound.
MELODIC
1 2
The mid-range of the sound being input at the point when the [ON/OFF] button is
pressed is recorded, and the recorded sound is output according to the level of the
sound being input.
, buttons (parameter 1) This sets the way in which the recorded sound is played.
BEAT
TIME control (parameter 2) This sets the way in which the recorded sound is played.
LEVEL/DEPTH control (param- This sets the balance between the original sound and the
eter 3) recorded sound.
X-PAD (parameter 4) This sets the way in which the recorded sound is played.
SLIP ROLL
1 2
The sound being input at the point when the [ON/OFF] is pressed is recorded, and
the recorded sound is output repeatedly according to the beat fraction set with the
[BEAT , ] buttons.
When the effect time changes, the input sound is recorded again.
Original
Changed from 1/2
Effect turned on
to 1/1
Roll
1/2 repeat
20
En
Time
Time
1/1 repeat
, buttons (parameter 1)
BEAT
TIME control (parameter 2)
LEVEL/DEPTH control (param-
eter 3)
X-PAD (parameter 4)
ROLL
1 2
The sound being input at the point when the [ON/OFF] is pressed is recorded, and
the recorded sound is output repeatedly according to the beat fraction set with the
[BEAT , ] buttons.
Original
Effect turned on
1/1 roll
, buttons (parameter 1)
BEAT
TIME control (parameter 2)
LEVEL/DEPTH control (param-
, ]
eter 3)
X-PAD (parameter 4)
REV ROLL
1 2
The sound being input at the point when the [ON/OFF] button is pressed is
recorded, and the recorded sound is reversed then output repeatedly according to
the beat fraction set with the [BEAT
Original
Effect turned on
1/1 reverse
roll
, buttons (parameter 1)
BEAT
TIME control (parameter 2)
LEVEL/DEPTH control (param-
eter 3)
X-PAD (parameter 4)
SND/RTN (MIDI LFO)
Connect an external effector, etc., here.
By pressing the [LFO FORM (WAKE UP)] button, MIDI-compatible software and
devices can be controlled using MIDI signals.
1
SND/RTN
Connect an external effector, etc., here.
0
9 9 9 9
0
0
-26 / 6 -26 / 6 -26 / 6 -26 / 6
12 12
12 12 -26 / 6 -26 / 6 -26 / 6 -26 / 6
TALK
OFF ON OVER
-26 / 6 -26 / 6 -26 / 6 -26 / 6
DJM-900SRT Serato DJ Edition
, buttons (parameter 1) —
BEAT
TIME control (parameter 2)
LEVEL/DEPTH control (param-
eter 3)
X-PAD (parameter 4)
MIDI LFO
The MIDI signal (0 – 127) waveform is changed according to the track's tempo.
Use these to set an effect time of 1/16 – 16/1 with respect to
the time of one beat of the BPM.
Use this to set the effect time.
10 to 4000 (ms)
Use this to set the balance between the original sound and
ROLL.
Use this to set the effect time.
Repeated
Use these to set an effect time of 1/16 – 16/1 with respect to
the time of one beat of the BPM.
Use this to set the effect time.
10 to 4000 (ms)
Use this to set the balance between the original sound and
ROLL.
Use this to set the effect time.
, ] buttons.
Reversed and repeated
Use these to set an effect time of 1/16 – 16/1 with respect to
the time of one beat of the BPM.
Use this to set the effect time.
10 to 4000 (ms)
Use this to set the balance between the original sound and
ROLL.
Use this to set the effect time.
SEND
RETURN
Effector
—
This adjusts the sound level input to the [RETURN] terminal.
—