Glossary - Sony TA-VE700 Mode D'emploi

Additional Information
Specifications
Amplifier section
POWER OUTPUT
Stereo mode
(DIN 1 kHz, 4 ohms)
Surround mode
(DIN 1 kHz, 4 ohms)
Front:
Centre:
Rear:
Frequency PHONO: RIAA
response
TUNER, CD, TAPE/MD,
Inputs
Sensitivity
PHONO
2.5 mV
(MM)
CD 200 mV
TAPE/
150 mV
MD,
TUNER,
VIDEO 1,
2, 3, TV/
LD
Outputs TAPE/MD REC OUT,
MIX AUDIO OUT
PHONES: Accepts low
– 20 dB
Muting
+10 dB at 70 Hz
BASS BOOST
TONE ±8 dB at 100 Hz and
18 EN
Video section
Inputs
90 W + 90 W
Outputs
90 W/ch
90 W
(only in the PRO
LOGIC mode)
25 W
equalization curve
±0.5 dB
General
System
VIDEO 1, 2, 3, TV/LD:
+0
10 Hz - 50 kHz dB
–1
Power
Impedance S/N
(weighting requirements
network,
input level)
Power
consumption
50 75 dB**
kilohms
(A, 2.5 mV)
AC outlets
Dimensions
50
82 dB**
kilohms
(A, 150 mV)
Mass (Approx.)
Supplied
accessories
** '78 IHF
Design and specifications are subject to
VIDEO 1, 2 AUDIO
change without notice.
OUT: Voltage 150 mV,
Impedance 10 kilohms
Voltage: 2 V
Impedance: 1 kilohms
and high impedance
headphones
10 kHz

Glossary

VIDEO 1, 2, 3, TV/LD
VIDEO IN:
1 Vp-p 75 ohms
Centre mode
VIDEO 1, 3 S VIDEO:
Setting of speakers to enhance Dolby Pro
Y: 1 Vp-p, unbalanced,
Logic Surround mode. To obtain the best
sync negative
possible surround sound, select one of the
C: 0.286 Vp-p,
following four centre modes according to
load impedance
your speaker system.
75 ohms
• NORMAL mode
VIDEO 1, 2, MONITOR
VIDEO OUT:
1 Vp-p 75 ohms
VIDEO 1, MONITOR
S VIDEO:
Y: 1 Vp-p, unbalanced,
sync negative
C: 0.286 Vp-p,
load impedance
75 ohms
Preamplifier section: Low-
noise NF type equalizer
Power amplifier section:
Pure-complimentary SEPP
220-230 V AC, 50/60 Hz
• WIDE mode
230 W
1 switched, total 100 W
430 x 157 x 355 mm
1
(17 x 6 / x 14 inches)
4
10.5 kg (23 lb 3 oz)
Remote commander
(remote) (1)
Size AA (R6) batteries (2)
• PHANTOM mode
Select NORMAL mode if you have front
and rear speakers and a small centre
speaker. Since a small speaker cannot
produce enough bass, the bass sound of
the centre channel is output from the front
speakers.
Centre
Front
Front
speaker
speaker (R)
speaker (L)
Rear Rear
speaker (L) speaker (R)
Select WIDE mode if you have front and
rear speakers and a large centre speaker.
With the WIDE mode, you can take full
advantage of Dolby Surround sound.
Centre
Front
Front
speaker
speaker (R)
speaker (L)
Rear Rear
speaker (L) speaker (R)
Select PHANTOM mode if you have front
and rear speakers but no centre speaker.
The sound of the centre channel is output
from the front speakers.
Front
Front
speaker (R)
speaker (L)
Rear Rear
speaker (L) speaker (R)