DSC tyco HSM2208 Guide Rapide

HSM2208 v1.1 Installation Instructions
8 Low-Current Output Expander Module
Use this Installation sheet with the Installation Manual of the equipment with which the
HSM2208 is used, such as the alarm controller, power supply, etc. Use the HSM2208 module to
add up to eight low-current programmable outputs to the compatible alarm controller models.
This module is compatible with PowerSeries Neo (HS2016, HS2032, HS2064, HS2128) and
PowerSeries Pro (HS3032, HS3128) panels.
Specifications
Temperature range: -10°C to + 55°C (0°C to + 49°C for UL/ULC listed systems).
l
Relative Humidity: Max. 93% relative humidity non-condensing.
l
Input rating: 10.8 VDC to 12.5 VDC/700 mA (includes 250 mA AUX maximum plus 50 mA for
l
each of the 8 outputs).
Maximum loading is shared with compatible alarm panel or power supply AUX output.
l
Board current draw: 60 mA (set and unset state/alarm and non-alarm state).
l
Board dimensions: 45 mm x 92 mm, weight 35 g.
l
AUX output ratings: 10.8 VDC to 12.5 VDC, -15% / + 15% when Input voltage is between
l
85% to 110% of rated value and output current is between 0 mA to 250 mA max.
PGM outputs: Open collector, switched to ground, 50 mA max.
l
Resettable fuse (PTC) used on circuit board instead of replaceable fuses. There are no ser-
l
viceable parts.
Maximum wire length from alarm panel: 1,000 ft'/305 m.
l
Terminal Descriptions
TMP- Used to tamper the cabinet in which the HSM2208 is mounted. Connect a normally closed
(NC) switch across TMP and BLK. If the tamper is not being used, connect a piece of wire across
TMP and BLK to remove the trouble condition.
NOTE:
There is a built-in tamper switch on the expander module located in the top left corner of the cir-
l
cuit board. If the cabinet in which the HSM2208 is mounted has the hardware required to depress
this tamper switch, do not connect anything to the TMP terminal.
Tamper protect is required for UL/ULC commercial/residential burglary installations.
l
AUX+ - There are two terminals for AUX power to provide easier wiring. These terminals are
used to provide power for devices. Maximum current draw must not exceed 250 mA. Connect the
positive lead of powered devices to either AUX+ and the negative to the proper output terminal
(O1 to O8).
CORBUS - The 4-wire Corbus connection is used by the panel to communicate with the module.
Connect the RED, BLK, YEL and GRN terminals to the Corbus terminals on the main control
panel.
Figure 1: Terminal Descriptions
01 to 08 - Wire the positive lead of the device to either AUX terminal and the negative lead to
the required output terminal (O1 to O8).
R é f é re nt ie l de c e rt if ic a t ion NF324/H58.
OR GANI SM ES C ER TI FI C ATEUR S :
C NPP C e rt
R out e de la C ha pe lle R é a nville
C S 22265
F- 27950 Sa int - M a rc e l www.c npp.c om Té l.
: +33 (0)2.32.53.63.63
Figure 2: Led indicator and relay output
Enclosures
You must install the HSM2208 in the same metallic cabinet as the alarm controller/power supply
or in a separate enclosure. Internal and/or external wiring for this module must be routed, sup-
ported, clamped or secured to reduce the possibility of: excessive strain on wire and on terminal
connections, loosening of terminal connections, and damage of conductor insulation.
You must install the HSM2208 in the metal enclosures listed below. You can install tamper pro-
tection switches on all enclosures, including door opening protection and/or removal from the
mounting position. Secure the doors using screws or a keylock.
Powerseries Pro enclosures:
Model HSC3010C (hinged door) made of 18 Ga steel, painted white, dimensions 372 mm x 412
l
mm x 114 mm.
Model HSC3010CR (hinged door) made of 18 Ga steel, painted red, dimensions 372 mm x 412
l
mm x 114 mm.
Model HSC3030CAR (hinged door) made of 18 Ga steel (base) and 16 Ga (door), painted white,
l
dimensions 375 mm x 412 mm x 114 mm.
Model HSC3020C (removable door) made of 18 Ga steel, painted white, dimensions 459 mm x
l
414 mm x 103 mm.
Model HSC3020CP (removable door) made of PC-ABS, color white, dimensions 368 mm x 489
l
mm x 108 mm.
Powerseries Neo enclosures:
Model PC5003C (removable door)
l
Model PC5003C (hinged door)
l
Model Power UC1
l
Model PC4003C
l
Model CMC-1
l
Model PC4050CAR (commercial burglary)
l
Model PC4050CR (ULC--S559)
l
NOTE: Use HSC3010C, PC4003C or PC5003C for UL/ULC installations.
Automatically Enrolling on the Alarm Panel
To enroll the HSM2208, complete the following steps:
1. Ensure that the system is not powered.
2. Connect the HSM2208 to the Corbus.
3. Power up the system.
4. Enter section [902] [000] and wait 1 minute.
5. To verify that the module is supervised, enter section [903] [003].
Manually Enrolling on the Alarm Panel
To enroll the HSM2208, complete the following steps:
1. Ensure that the system is not powered.
2. Connect the HSM2208 to the Corbus.
3. Power up the system.
4. Enter section [902] [001].
5. Enter the module serial number.
6. Enter section [903] [003] to verify that the module is supervised.
Status LED
The HSM2208 is equipped with a status LED to indicate the current condition of the module. If
the HSM2208 is operating correctly, the status LED flashes briefly every 10 seconds. When a
trouble condition is present, the status LED displays a series of flashes then remains blank for
1.5 seconds. The number of flashes indicates the trouble condition, as outlined below.
Number of Flashes
1
2
3
Table 1: Status LED
AFNOR Cert if icat ion 11, rue Francis de Pressensé F-93571 LA PLAI NE
Saint Denis Cedex www.marque-nf .com Tél : + 33 (0)1.41.62.80.00
Trouble Condition
Module not enrolled
Alarm Panel supervision trouble
CORBUS low voltage
29010168R002
Limited Warranty
Digit alSecurit y Cont rols (DSC) warrant s t hat f or aperiod of t welve mont hs f rom t he dat e of purchase, t he product shall be f ree of def ect s in mat erials and workmanship under normal use and t hat in
f ulf ilment of any breach of such warrant y, DSC shall, at it s opt ion, repair or replace t he def ect ive equipment upon ret urn of t he equipment t o it s f act ory. This warrant y applies only t o def ect s in part s
and workmanshipand not t odamage incurred in shipping or handling, or damage due t o causes beyondt he cont rol of DSC such as light ning, excessive volt age, mechanical shock, wat er damage, or damage
arisingout of abuse, alt erat ion or improper applicat ionof t he equipment .
The f oregoing warrant y shall apply only t o t he original buyer, and is and shall be in lieu of any and all ot her warrant ies, whet her expressed or implied and of all ot her obligat ions or liabilit ies on t he part of
DSC. This warrant y cont ains t he ent ire warrant y. Digit al Securit y Cont rols neit her assumes responsibilit y f or, nor aut horizes any ot her person purport ing t o act on it s behalf t o modif y or t ochange t his
warrant y, nor t o assume f or it any ot her warrant y or liabilit y concerning t his product . I n no event shall DSC be liable f or any direct or indirect or consequent ial damages, loss of ant icipat ed prof it s, loss
of t ime or any ot her losses incurred by t he buyer inconnect ion wit h t he purchase, inst allat ion or operat ion or f ailureof t his product .
Warning: Digit al Securit y Cont rols recommends t hat t he ent iresyst em be complet ely t est ed on a regular basis. However, despit e f requent t est ing, and due t o, but not limit ed t o, criminal t ampering or
elect rical disrupt ion, it is possible f or t his product t o f ail t o perf orm as expect ed.
I MPORTANT - READ CAREFULLY: DSC Sof t ware purchased wit h or wit hout Product s and Component s is copyright edand is purchased under t he f ollowing license t erms:
This End- User License Agreement ("EULA") is a legal agreement bet ween You (t he company, individual or ent it y who acquired t he Sof t ware and any relat ed Hardware) and Digit al Securit y Cont rols, a divi-
sion of Tyco Saf et y Product s Canada Lt d. ("DSC"), t he manuf act urer of t he int egrat ed securit y syst ems and t he developer of t he sof t ware and any relat ed product s or component s ("HARDWARE") which
You acquired. I f t he DSC sof t ware product ("SOFTWARE PRODUCT" or "SOFTWARE") is int ended t o be accompanied by HARDWARE, and is NOT accompanied by new HARDWARE, You may not use, copy or
inst allt he SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes comput er sof t ware, and may includeassociat ed media, print ed mat erials, and "online" or elect ronic document at ion. Any sof t ware
provided along wit h t he SOFTWARE PRODUCT t hat is associat ed wit h aseparat e end- user license agreement is licensed t o You under t he t erms of t hat license agreement .
Byinst alling, copying, downloading, st oring, accessing or ot herwise using t he SOFTWARE PRODUCT, You agree uncondit ionally t o bebound by t he t erms of t his EULA, even if t his EULA is deemedt o be a
modif icat ionof any previous arrangement or cont ract . I f You do not agree t o t he t erms of t his EULA, DSC is unwilling t o license t he SOFTWARE PRODUCT t o You, and You have no right t o use it .
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is prot ect ed by copyright laws and int ernat ional copyright t reat ies, as well as ot her int ellect ual propert y laws and t reat ies. The SOFTWARE PRODUCT is licensed, not sold.
1.GRANT OF LI CENSE This EULA grant s You t he f ollowing right s:
(a) Sof t ware I nst allat ion and Use - For each license You acquire, You may have only one copy of t he SOFTWARE PRODUCT inst alled.
(b) St orage/Net work Use - The SOFTWARE PRODUCT may not be inst alled, accessed, displayed, run, sharedor used concurrent ly onor f rom dif f erent comput ers, including aworkst at ion, t erminal or ot her
digit alelect ronic device ("Device"). I n ot her words, if You have several workst at ions, You will have t o acquire a license f or each workst at ion where t he SOFTWARE will be used.
(c) BackupCopy - You may make back- up copies of t he SOFTWARE PRODUCT, but You may only have one copy per license inst alled at any given t ime. You may use t he back- up copy solely f or archival pur-
poses. Except as expressly provided in t his EULA, You may not ot herwise make copies of t he SOFTWARE PRODUCT, including t he print ed mat erials accompanying t he SOFTWARE.
2.DESCRI PTI ON OF OTHER RI GHTS AND LI MI TATI ONS
(a) Limit at ions on Reverse Engineering, Decompilat ion and Disassembly - You may not reverse engineer, decompile, or disassemblet he SOFTWARE PRODUCT, except and only t o t he ext ent t hat such act iv-
it y is expressly permit t ed by applicable law not wit hst anding t his limit at ion. You may not make any changes or modif icat ions t o t he Sof t ware, wit hout t he writ t en permission of an of f icer of DSC. You
may not removeany propriet arynot ices, marks or labels f rom t he Sof t ware Product . You shall inst it ut e reasonable measures t oensure compliance wit h t he t erms and condit ions of t his EULA.
(b) Separat ion of Component s - The SOFTWARE PRODUCT is licensed as a single product . I t s component part s may not be separat ed f or use on more t han one HARDWARE unit .
(c) SingleI NTEGRATED PRODUCT - I f You acquired t his SOFTWARE wit h HARDWARE, t hen t he SOFTWARE PRODUCT is licensed wit h t he HARDWARE as a single int egrat ed product . I n t his case, t he
SOFTWARE PRODUCT may only be used wit h t he HARDWARE as set f ort h in t his EULA.
(d) Rent al - You may not rent , lease or lend t he SOFTWARE PRODUCT. You may not make it available t o ot hers or post it on a server or web sit e.
(e) Sof t ware Product Transf er - You may t ransf er all of Your right s under t his EULA only as part of a permanent sale or t ransf er of t he HARDWARE, provided You ret ain no copies, You t ransf er all of
t he SOFTWARE PRODUCT (including all component part s, t he media and print ed mat erials, any upgrades and t his EULA), and provided t he recipient agrees t o t he t erms of t his EULA. I f t he SOFTWARE
PRODUCTis an upgrade, any t ransf er must also include all prior versions of t he SOFTWARE PRODUCT.
(f ) Terminat ion- Wit hout prejudice t o any ot her right s, DSC may t erminat e t his EULA if You f ail t o comply wit h t he t erms and condit ions of t his EULA. I n such event , You must dest roy all copies of t he
SOFTWARE PRODUCT and all of it s component part s.
(g) Trademarks - This EULA does not grant You any right s in connect ion wit h any t rademarks or service marks of DSC or it s suppliers.
3.COPYRI GHT - All t it le and int ellect ual propert y right s in and t o t he SOFTWARE PRODUCT (including but not limit edt o any images, phot ographs, and t ext incorporat ed int o t he SOFTWARE PRODUCT), t he
accompanyingprint ed mat erials, and any copies of t he SOFTWARE PRODUCT, are owned byDSC or it s suppliers. You may not copy t he print ed mat erials accompanying t he SOFTWARE PRODUCT. All t it le
and int ellect ual propert y right s in and t o t he cont ent which may be accessed t hrough use of t he SOFTWARE PRODUCT are t he propert y of t he respect ive cont ent owner and may be prot ect ed by applicable
copyright or ot her int ellect ual propert y laws and t reat ies. This EULA grant s You no right s t o use such cont ent . All right s not expressly grant edunder t his EULA are reserved by DSC and it s suppliers.
4.EXPORT RESTRI CTI ONS - You agree t hat You will not export or re-export t he SOFTWARE PRODUCT t o any count ry, person, or ent it y subject t o Canadian export rest rict ions.
5.CHOI CE OF LAW - This Sof t ware License Agreement is governed by t he laws of t he Province of Ont ario, Canada.
6.ARBI TRATI ON - All disput es arising in connect ion wit h t his Agreement shall be det ermined by f inal and binding arbit rat ionin accordance wit h t he Arbit rat ion Act , and t he part ies agree t o bebound by
t he arbit rat or's decision. The place of arbit rat ion shall beToront o, Canada,and t he language of t he arbit rat ionshall be English.
LIMITED WARRANTY
(a) NO WARRANTY - DSC PROVI DES THE SOFTWARE "AS I S" WI THOUT WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WI LL MEET YOUR REQUI REMENTS OR THAT OPERATI ON OF THE
SOFTWARE WI LL BE UNI NTERRUPTED OR ERROR-FREE.
(b) CHANGES I N OPERATI NG ENVI RONMENT - DSC shall not be responsiblef or problems causedby changes in t he operat ing charact erist ics of t he HARDWARE, or f or problems in t he int eract ion of t he
SOFTWARE PRODUCT wit h non- DSC-SOFTWARE or HARDWARE PRODUCTS.
(c) LI MI TATI ON OF LI ABI LI TY; WARRANTY REFLECTS ALLOCATI ON OF RI SK - I N ANY EVENT, I F ANY STATUTE I MPLI ES WARRANTI ES OR CONDI TI ONS NOT STATED I N THI S LI CENSE AGREEMENT, DSC'S
ENTI RE LI ABI LI TY UNDER ANY PROVI SI ON OF THI S LI CENSE AGREEMENT SHALL BE LI MI TED TO THE GREATER OF THE AMOUNT ACTUALLY PAI D BY YOU TO LI CENSE THE SOFTWARE PRODUCT AND FI VE
CANADI AN DOLLARS (CAD$5.00). BECAUSE SOME JURI SDI CTI ONS DO NOT ALLOW THE EXCLUSI ON OR LI MI TATI ON OF LI ABI LI TY FOR CONSEQUENTI AL OR I NCI DENTAL DAMAGES, THE ABOVE
LI MI TATI ON MAY NOT APPLY TO YOU.
(d) DI SCLAI MER OF WARRANTI ES - THI S WARRANTY CONTAI NS THE ENTI RE WARRANTY AND SHALL BE I N LI EU OF ANY AND ALL OTHER WARRANTI ES, WHETHER EXPRESSED OR I MPLI ED (I NCLUDI NG
ALL I MPLI ED WARRANTI ES OF MERCHANTABI LI TY OR FI TNESS FOR A PARTI CULAR PURPOSE) AND OF ALL OTHER OBLI GATI ONS OR LI ABI LI TI ES ON THE PART OF DSC. DSC MAKES NO OTHER
WARRANTI ES. DSC NEI THER ASSUMES NOR AUTHORI ZES ANY OTHER PERSON PURPORTI NG TO ACT ON I TS BEHALF TO MODI FY OR TO CHANGE THI S WARRANTY, NOR TO ASSUME FOR I T ANY OTHER
WARRANTY OR LI ABI LI TY CONCERNI NG THI S SOFTWARE PRODUCT.
(e) EXCLUSI VE REMEDY AND LI MI TATI ON OF WARRANTY - UNDER NO CI RCUMSTANCES SHALL DSC BE LI ABLE FOR ANY SPECI AL, I NCI DENTAL, CONSEQUENTI AL OR I NDI RECT DAMAGES BASED UPON
BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLI GENCE, STRI CT LI ABI LI TY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES I NCLUDE, BUT ARE NOT LI MI TED TO, LOSS OF PROFI TS, LOSS OF THE
SOFTWARE PRODUCT ORANY ASSOCI ATED EQUI PMENT, COST OF CAPI TAL, COST OF SUBSTI TUTE ORREPLACEMENT EQUI PMENT, FACI LI TI ES OR SERVI CES, DOWN TI ME, PURCHASERS TI ME, THE CLAI MS OF
THI RD PARTI ES, I NCLUDI NG CUSTOMERS, AND I NJURY TO PROPERTY. WARNI NG: DSC recommends t hat t he ent ire syst em be complet ely t est ed ona regular basis. However, despit e f requent t est ing, and
due t o, but not limit ed t o, criminal t ampering or elect rical disrupt ion, it is possible f or t his SOFTWARE PRODUCT t o f ail t o perf orm as expect ed.
FCC COMPLIANCE STATEMENT
CAUTI ON: Changes or modif icat ions not expressly approved by DSC could void your aut horit y t o use t his equipment .
This equipment generat es and uses radio f requency energyand if not inst alled and used properly, in st rict accordance wit h t he manuf act urer's inst ruct ions, may cause int erf erence t o radio and t elevision
recept ion. I t has been t ype t est edand f ound t o comply wit h t he limit s f or Class B device in accordance wit h t he specif icat ions in Subpart "B" of Part 15 of FCC Rules, which are designed t o provide reas-
onableprot ect ion against such int erf erence in any resident ial inst allat ion. However, t here is no guarant ee t hat int erf erence will not occur in a part icular inst allat ion. I f t his equipment does cause int er-
f erencet o t elevision or radio recept ion, which can be det ermined by t urning t he equipment of f and on, t he user is encouraged t o t ry t o correct t he int erf erence by one or more of t he f ollowing
measures:
•Re- orient t he receiving ant enna
•Relocat e t he alarm cont rol wit h respect t o t he receiver
•Move t he alarm cont rol away f rom t he receiver
•Connect t he alarm cont rol int o a dif f erent out let so t hat alarm cont rol and receiver are ondif f erent circuit s.
I f necessary, t he user should consult t he dealer or an experiencedradio/t elevision t echnician f or addit ional suggest ions. The user may f ind t he f ollowing booklet prepared by t he FCC usef ul: "How t o
I dent if y and Resolve Radio/TelevisionI nt erf erence Problems". This booklet is available f rom t he U.S. Government Print ing Of f ice, Washingt on D.C. 20402, St ock # 004- 000- 00345-4.
Industry Canada
CAN I CES- 3(B) / NMB- 3(B)
EN CERTIFICATION
The Model HSM2208 Out put Modulehas been cert if ied by Telef icat ion according t o EN50131- 1:2006+ A1:2009 and EN50131- 3:2009Type A f or Grade 2, Class I I when inst alled in t he PC5003C enclosure.
HSM2208 v1.1 - Instructions d'installation
Module d'extension de 8 sorties à faible courant
Cette fiche d'installation doit être utilisée avec le manuel d'installation de l'équipement qui ali-
mente le HSM2208, tel que le contrôleur d'alarme, l'alimentation électrique, etc. Utilisez le mod-
ule HSM2208 pour ajouter jusqu'à huit sorties programmables à faible courant sur les modèles de
contrôleur d'alarme compatibles. Ce module est compatible avec les centrales PowerSeries Neo
(HS2016, HS2032, HS2064, HS2128) et PowerSeries Pro (HS3032, HS3128).
Caractéristiques
Plage de température : -10 °C à + 55 °C (0 °C à + 49 °C pour les systèmes homologués UL/ULC)
l
Humidité relative : 93 % d'humidité relative maximale, sans condensation.
l
©2018 Tyco Security Products www.d-
sc.com Tech. Support: 1-800-387-3630