Manual Ignition - Campingaz Blue Flame L Mode D'emploi

f Use no. 24 wrench to close the nut on the flexible tube
of the appliance, or when removing it.
y Use a wrench to fix the outlet connection of the regulator
when attaching the flexible tube, or when removing it.
y Air tightness is to be verified following the instructions in
paragraph F).
Check that the flexible hose stretches out normally without
twisting or pulling and does not come into contact with the hot
sides of the barbecue. It should be replaced when the expiry
date on the hose is passed or whenever it is damaged or
develops surface cracks.
■ Belgium, Luxembourg, united kingdom, Ireland,
Portugal, Spain, Italy, Croatia, Greece, Netherlands,
Czech Republic, Slovakia, Hungary, Slovenia, Norway,
Sweden, Denmark, Finland, Bulgaria, Turkey, Romania,
Poland, Estonia, Switzerland (depending on model):
The barbecue is equipped with a circular connector. It should
be used with flexible hose that is suitable for use with butane
and propane gas. Hose length should not exceed 1.20 meter. It
should be replaced if it is damaged or cracked, when required
by national regulations or at the end of the part lifecycle. Do not
pull or pierce the hose.
Keep hose away from any parts of the barbecue that get hot.
Check that the flexible hose stretches out normally, without
twisting or pulling.
Germany, Austria, Switzerland (depending on model):
The barbecue should be used with flexible tubing that is
suitable for use with butane and propane gas. Hose length
should not exceed 1.50 meter. It should be replaced if it is
damaged or cracked, when required by national regulations
or at the end of the part life-cycle. Do not pull or pierce the
tubing. Keep away from any parts of the barbecue that get hot.
Check that the flexible hose stretches out normally, without
twisting or pulling.
GB
Attaching the flexible tube (see Fig. 3): use two wrenches
to close the flexible tube on the gas connection of the
appliance:
f Use no. 10 wrench to tighten the connector.
f Use no. 17 wrench to tighten the nut on the tubing.
F. CHECkING FOR GAS LEAkS
1. Work outside, away from all sources of ignition. Do not
smoke.
2. Make sure the control knobs are in the "off" (O) position.
3. Connect the flexible tubing to the connector and barbecue
as described in part e).
4. Fit the regulator onto the gas cylinder in accordance with
its instructions.
5. Use a gas leak solution to test for leaks. Important: never
use a naked flame to check for gas leaks.
6. (Fig. 4) Apply the solution to the connections cylinder/
regulator/ hose/appliance (the control knobs should remain
closed: off position (O)). Open the gas cylinder valve.
7. Bubbles in the gas leak solution indicate that there are
gas leaks.
8. The leak can be stopped by tightening any hose connection
or replacing any faulty component. The barbecue must not
be used until the leak is stopped.
9. Close the valve on the gas cylinder.
Important:
Check for leaks at least once per year and each time the gas
cylinder is replaced.
Never use a flame to detect a leak.
G. PRIOR TO uSE
Never use the appliance until the instructions have been read
carefully and understood. Additionally, ensure that :
y There are no leaks.
y (Fig.5) the venture tubes are not blocked (example : spider
webs).
y (Fig.1) The hose does not touch any components which
may get hot.
y The lid is not in closed position (depending on models).
y This appliance is equipped with wide holes for air circulation.
Ensure that these holes are not obstructed.
H. IGNITION OF THE BuRNERS
Never light the appliance with the lid closed, only with the
lid opened.
y Attach the protective lid to the back of the device. (Fig. 6)
y Make sure that the control knobs are in the "OFF" position
(O).
y Press and turn the adjustment lever counter-clockwise and
put it in a full flow position (
y If your appliance is equipped with a piezoelectric igniter:
Press immediately on the igniter button (
(Fig. 8)
If the burner does not ignite after 4 or 5 attempts, wait 5
minutes and then repeat the operation.
y If your device is equipped with an electronic igniter
using sparks:
Press immediately on the switch (
occurs. Continue pressing for a few seconds until the burner
is lit. (Fig. 8)
y If the burner does not ignite after 4 or 5 attempts, wait 5
minutes and then repeat the operation.
y Once a burner is ignited, there are two options for lighting
another burner:
f Firstly, repeat the lighting operation described above;
f Secondly, light the burner to the right or left of the first
burner lit by turning the adjustment button to the full flow
position ( ).
y If the piezoelectric ignition or the electronic ignition doesn't
work, use the manual ignition (following paragraph).
I. MANuAL IGNITION
In case of non-working automatic ignition, set the control knobs
on « OFF » (O).
Remove grease cup. Light a match and then bring it toward the
burner through the grease cup hole of the plancha.
Push the control knob and turn it counterclockwise until it is in
the full flow position (
Put the grease cup back in place with protective gloves, being
sure to correctly position the drippings evacuation hole.
J. J. SHuTTING OFF OF THE APPLIANCE
Return the control knobs to the "OFF" position (O), then close
the cylinder valve.
k. REPLACING THE GAS CyLINDER
y Always work in a well ventilated area and never in the
presence of a flame, spark or heat source.
y Return the control knobs to the "off" position (O) then close
the cylinder valve.
y Remove the regulator, check that the sealing joint is in good
condition.
y Put the full cylinder in place, refit the regulator, taking care
not to apply stress to the hose. Check for gas leaks.
L. OPERATION
10
). (Fig. 7)
) until it clicks.
). A burst of sparks
).