Terms And Definitions Acc. To Standard; Description Of Symbols - Wisniowski INTRO 600 Notice De Montage Et De Fonctionnement

EN
SPIS TREŚCI
1. Overview ........................................................................................................ 12
2. Terms and definitions acc. To standard........................................................ 12
3. Description of symbols .................................................................................. 12
4. Build description and technical specification .............................................. 13
4.1. Technical specifications ...................................................................... 13
5. Applications and intended use ..................................................................... 13
6. Safety guidelines ........................................................................................... 13
7. Required installation conditions .................................................................... 13
8. Drive installation errors .................................................................................. 14
9. Environmental protection ............................................................................... 14
10. Controller ........................................................................................................ 14
11. Installation instructions ................................................................................... 14
12. Safety requirements ....................................................................................... 14
13. Installation instructions ................................................................................... 14
13.1. Installation sequence .......................................................................... 15
13.2. Photocells circuit diagram .................................................................. 15
13.3. Bell-push circuit diagram .................................................................... 15
13.4. Circuit diagram for radio receiver ..................................................... 15
13.5. Warning lamp connection diagram .................................................. 15
13.6. Drive unit adjustment........................................................................... 15
13.7. Overload adjustment .......................................................................... 15
13.8. Manual control buttons ...................................................................... 15
14. Extra requirements ......................................................................................... 16
15. Dismantling the drive ..................................................................................... 16
16. Controller installation sequence ................................................................... 16
16.1. Controller programming .................................................................... 16
17. Operation issues ............................................................................................ 17
18. Operating instruction ..................................................................................... 17
18.1. Manually operated door ................................................................... 18
18.2. Electrically driven door ....................................................................... 18
19. Routine maintenance instructions .................................................................. 18
20. Warranty conditions ...................................................................................... 18
21. The equipment of the INTRO drive .............................................................. 19
22. FAQ .................................................................................................................20
1. OVERVIEW
[A000131] This Installation and Operating Manual is intended for professional
fitters and product owners. It contains the essential information to guarantee
safe installation and use, as well as the information about correct care and
maintenance of the products.
Before beginning installation, read the entire manual, follow its guidelines, and
perform all activities in the described order. The product and its separate elements
shall be installed in accordance with the manual. Follow the guidelines for assem-
bly and use to allow for correct assembly and to ensure a long and reliable use.
• [A000094] The scope of activities a Professional Installer and the
Owner can perform is described further in this manual.
• [C000445] The electric drive unit or the controller can only be in-
stalled and adjusted by a PROFESSIONAL INSTALLER who is
competent in automation and mechanical engineering equipment
for residential use and must do the installation and adjustments in
accordance with the current laws of the country of use.
• [A000104] Failure to comply with the recommendations and
suggestions contained in this Installation and Operating Manu-
al will release the Manufacturer from all liability and warranty
obligations.
[A000120] The Manual applies to several product model variants.
[B000203] The door is also referred to as the "product".
[B000204] The control device is also referred to as the "drive unit".
[A000097] The manual covers the installation of the products with standard
equipment and optional equipment components. The scope of standard and
optional equipment is defined in the commercial offer.
[A000099] The reference drawings found in the manual may vary in finish
details. When necessary, the details are shown in separate drawings.
When installing the product, follow the occupational health and safety regula-
tions for installation and fitting works with the use of power tools, depending on
the applied installation technology, and consider the applicable standards, laws
and reference construction documentation.
When renovating/fitting, protect all components against splashing of plaster,
cement, gypsum, etc. These may leave stains of dirt.
After completing the installation and checking for correct operation of product
hand over the Installation and Operating Manual to the owner. The Installation and
Operating Manual should be protected against being destroyed and kept it safe.
If the product is installed using components from various manufacturers or sup-
pliers, the door fitter becomes the product manufacturer.
12
Assembly and Operating Instructions - Drive unit for garage doors INTRO
[A000122] The Manufacturer shall not be liable for any damage or operating
malfunctions caused by use of the product with equipment from other suppliers.
Such use also voids the warranty issued by the Manufacturer.
[B000129] The product shipping packaging is intended to protect the product
during transport only. Protect the products in the packaging against weather.
Keep the packed product on a hard and dry surface (which must be flat, level
and resist variations in indoor conditions) located in sheltered rooms that are dry
and well-ventilated; the storage location must be free from all external conditions
which may damage the product components and its packaging. Do not store
in wet rooms and/or rooms with vapours which may damage paint coats and/
or galvanic coats.
[B000025] Airtight foil packaging must be unsealed when storing the doors to
avoid adverse change of microclimate inside the packaging. Failure to do so
may result in the damage of painted and zinc plated coating.
[C000443] No elements of the drive may be modified or removed. Doing so
may influence its safe operation. Changing drive subassemblies is forbidden.
[A000134] Copying these Instructions without prior written permission and fur-
ther copy contents verification by the Manufacturer is prohibited.
[C000075] The wiring system and the electric shock protection installations are
defined by current norms and regulations. Only a qualified installer is allowed
to perform electrical works.
• The drive feed circuit should be equipped with a cut-off protection, a residual
current circuit-breaker, and an overcurrent protection.
• The gate power supply system should be executed as a separate electrical
circuit.
• Grounding of the drive unit is obligatory and should be done in the first place.
• Disconnect power supply prior to any works on the electrical system. Discon-
nect any backup batteries, if used.
• In case of the fuse activation, first find the reason and remove the problem,
and only then redeploy the gate.
• In case a problem persists and information from this instruction fails to help,
contact the manufacturer technical department.
• Any rework or repairs on the system should be conducted only by a profes-
sional installer.
• Usage other than stated in this instruction is not allowed.
• Neither children nor adults should stay within the gate operating area.
2. TERMS AND DEFINITIONS ACC. TO STANDARD
[B000199] Explanation of warning signs used in the Instruction:
Attention! - warning sign used to denote the attention.
Information - warning sign used to denote important
information.
Reference mark - sign referring to a given paragraph in the
Assembly Instruction.
Professional Installer - competent person or organization, offering to third
parties door installation services, including its improvement (according to EN
12635).
Owner - a natural or legal person who has legal title to administer the door,
and takes responsibility for its operation and use (acc. to EN 12635).
Report Book - a book containing the main data about the door, and which has
a specially designated places for records about inspections, tests, maintenance and
various repairing works or modifications to the door (according to EN 12635).
[B000213] Door operating cycle - one opening and closing movement of
the door.
3. DESCRIPTION OF SYMBOLS
- option
- manually operated
- automatic
[B000205]
Fd - the maximum force measured with an instrument during the dy-
namic activity time TD
Fs - the maximum force measured with an instrument outside the
dynamic activity time TD
Td - the time during which the measured force exceeds 150 N
Tt - the time during which the measured force exceeds 25 N
IIiO/INTRO/09/2017/ID-95874 Technical Description
+