MSW C-SAW210 Manuel D'utilisation page 6

TECHNICAL DETAILS
Product name Circular Saw
Model C-SAW210 C-SAW254T
Voltage [V] 230
Power [W] 900 1500
Max power 2280 2875
consumption [W]
Frequency [Hz] 50
Protection class II I
Working mode S1
Maximum rotational 4800 5000
speed (without load)
[rev/min]
Maximum cutting 45 75
depth at 90° [mm]
Maximum cutting 25 50
depth at 45° [mm]
Blade tilt range 0-45°
Dimensions [mm] 567x404x370 1010x955x1056
Table dimensions 524x400 625x445
[mm]
Dimensions of - Side: 620x248
Rear: 320x438
extendible surfaces
[mm]
Blade diameter 210 254
[mm]
Blade bore size 30
[mm]
Splitting wedge 2,0 2,5
thickness [mm]
Sound power level 106,7 dB(A) 105 dB(A)
L Uncertainty Uncertainty
WA
K=3dB(A) K = 3dB(A)
Sound pressure 93,7dB(A) 90 dB(A)
level L Uncertainty Uncertainty
pA
K=3dB(A) K=3dB(A)
Number 24
of saw teeth
Weight [kg] 13,3 28,7
USAGE PURPOSE
The device is designed for cutting wood.
Any damage resulting from a non-conform use of the
device is payable by the user!
10
PRINCIPLE OF OPERATION
Assembly
C-SAW210
6
4
7
1 2 3 5
8
9
10
11
18
17
6 19 5
13 12
15 14
16
1. Worktable
2. Groove
3. Angle cutting guide
4. Guide knob
5. Splitting wedge
6. Blade guard
7. Saw blade
8. Base insert
9. Parallel guide
10. Parallel guide mounting bolt
11. Scale
12. Blade height adjustment knob
13. Blade tilt angle adjustment knob
14. Overload breaker
15. Switch On/Off
16. Rubber pads
17. Push stick bracket
18. Push stick
19. Blade guard mounting bolt
C-SAW254T
5 6 7 8 9 4
4 10
3
11
12
2
13
14
15
16
1
18 17
23
22
19
21
20
7
24
8
25
14
Rev. 10.10.2017
1. Switch On/Off
2. Table supports
3. Guide rail
4. Groove
5. Table lengthwise extension
6. Worktable
7. Blade guard
8. Splitting wedge
9. Saw blade
10. Parallel guide
11. Table width-wise extension
12. Parallel guide lever
13. Blade tilt angle adjustment knob
14. Push stick
15. Blade tilt angle scale
16. Blade height adjustment knob
17. Housing
18. Top stand bar
19. Stand leg
20. Rubber pads
21. Bottom stand bar
22. Support
23. Overload breaker
24. Suction hose coupling
25. Push stick bracket
BEFORE FIRST USE
Upon receipt of the goods, check the packaging for
integrity and open it. If the packaging is damaged, please
contact your trans¬port company and distributor within 3
days, and document the damages as detailed as possible.
Do not turn the package upside down! When transporting
the package, please ensure that it is kept horizontal and
stable. Please keep all packaging materials (cardboard,
plastic tapes and styrofoam), so that in case of a problem,
the device can be sent back to the service centre in accurate
condition.
DISPOSING OF PACKAGING
The various items used for packaging (cardboard, plastic
straps, polyurethane foam) should be conserved, so that
the device can be sent back to the service center in best
conditions in case of problem!
INSTALLING THE APPLIANCE
Appliance location
The work surface where the device will be located must be
suitable for the size of the appliance, please refer to the
measure¬ments. The work surface must be levelled, dry,
heat-resistant and at a fitting height from the ground to
enable a proper use of the de¬vice.
The power cord connected with the appliance must be
properly grounded and correspond to the technical details.
Preparing for use
Model C-SAW210
• Remove the device from the box and unwrap
protective films.
• Use knob (12) to extract saw blade with the splitting
wedge.
• Mount blade guard (6) by attaching it to the splitting
wedge (5) using a bolt in the guard.
Rev. 10.10.2017
6 19 5
• Place the push stick (18) on the bracket (17) on the
right side.
• Double check whether the saw blade (7) is correctly
mounted, there is no play and that it does not rub on
other saw elements by gently spinning it with your
hand. Make sure that the saw rotation direction is
in accordance with the rotation direction shown on
the saw blade.
• Always make sure that the saw blade and the
splitting wedge are in the same plane and that the
wedge edge is at the right distance (3-5 mm) away
from the saw blade teeth.
Model C-SAW254T
• Remove the device from the box and unwrap
protective films.
• Set the circular saw with the work table (6) on the
bottom.
• Assemble to saw stand:
a) Screw the legs (19) to the openings in the saw
housing.
19
b) Press the rubber pads (20) into the bottom of
the legs (19).
c) Screw together the legs (19), top bars (18) and
bottom bars (21) using bolts (included).
18
21
d) Attach supports (22) to the rear legs (19), see
diagram below.
22 19
• Attach additional work surfaces (5) and (11) as shown
on the diagram below. To mount the work-surface (5)
use longer supports than those for work-surface (11).
11