Indexa VA-707/2 Mode D'emploi page 15

Danger!
!
Do not leave small children unattended with the device, packaging material or small
parts! Otherwise there is a risk to life from suffocation!
!
When you drill holes or install the fastenings make sure that you do not damage any
cables or pipes carrying gas, electricity, water or telecommunications! Otherwise there
is a risk to life and limb!
!
Handle all cables carefully! Place the cable in such a position that it cannot be damaged
or become a trip hazard. Fasten the cable in place with an adequate number of cable
clips. Do not pull the cable over sharp edges or allow it to become squashed or clamped
in other ways. Otherwise there is a risk to life and limb!
!
If you use the device for monitoring babies or small children ensure that the camera
and cable are out of reach of children. Otherwise there is a risk to life and limb!
!
Do not allow the mains adapter to come into contact with moisture! Otherwise there is
a danger to life!
!
An observation system does not replace your duty of supervision and care.
Attention!
!
Operate the monitor only with the supplied mains adapter. Check before connecting
the mains adapter to the mains that the electricity supply circuit is 230 V ~ AC, 50 Hz
and is fitted with a fuse or trip.
!
Protect the cameras, cables and Monitor from strong magnetic or electric fields!
!
Do not place the device near fire, heat, or subject it to prolonged high temperatures!
!
Protect the device from violent mechanical loads and vibrations!
!
Use the device only with the supplied original parts or original accessories!
!
Before assembling and bringing the device into use check the supplied items for
damage and completeness!
!
If the device is damaged (e.g. transport damage) do not connect it. If in doubt ask your
customer service centre. Repairs and interference with the device may only be carried
out by trained specialists.
!
Use a dry or slightly moist cloth for cleaning the device. Never immerse the device in
water.
Planning where you install the device
Before you install the cameras you must first plan what to do at the installation site.
Check that the cameras work satisfactorily at the installation site before you install them.
Observe the following points:
!
The cameras should be attached in such a way that as little direct light or direct sunlight
as possible strikes the lens. When considering this, remember that the position of the
sun does not remain constant. The camera image is best checked before it is installed.
To do this connect the system, sselect the camera image on the monitor and hold the
camera in the planned position. If necessary alter the position of the camera until you
obtain your desired picture coverage.
!
The cameras have an infrared light for the adjacent area for better facial recognition.
Additional lighting in the area at night will improve the image quality from the camera.
!
Ensure that the location of the cameras and of the monitor are dustfree and
vibrationfree and that there is adequate air circulation.
!
Ensure that there is a mainspower supply near to the monitor
!
Take account of the cable length between the cameras and the monitor
!
For outdoor use, choose a location for the camera that is protected from direct rainfall.
The cable connector must be insulated so that there is no water ingress
!
Ensure that there is a suitable access hole for the cable.
!
The monitor must be positioned on a flat and stable surface.
Mounting and connection of the cameras
!
Attach the bracket [7] with the supplied screws to a suitable surface eg. a wall or ceiling
(see Fig. B). If necessary use the supplied wall plugs.
!
For wall mounting screw the thread of the bracket into the thread for wall mounting
[6] on the camera. For ceiling mounting screw the thread of the bracket into the thread
for ceiling mounting [3] on the camera.
!
Fix the orientation of the camera by tightening the fixing screw on the bracket.
!
Connect the connector [4] with the plug from a cable [8]
!
Connect the yellow plug of the cable [8] with the yellow socket of a connection cable
[9]
!
Connect the white plug of the cable [8] with the white socket of a connection cable [9]
!
Connect the black socket of the cable [8] with the red plug of a connection cable [9]
!
Connect the black plugs of the connection cables [9] into one of the sockets [22/23] on
the monitor
!
Repeat the above steps for the second camera
!
The cameras are ready for use when the monitor is connected to the power supply
GB - 17