Cleaning, Maintenance And Ordering Spare Parts - EINHELL PICOBELLA Instructions D'origine

6.4.3 Cleaning smooth, unsealed paver and
stone surfaces
Note: Use the MEDIUM brush to do this (to fi t the
brush, see section 5.5).
•
Actuate the left side (Fig. 18 / Item V) of the
changeover switch (forward). The equipment
will pull away from you (standard direction of
rotation).
•
In case of certain kinds of stubborn dirt, it can
be helpful to clean using both directions of ro-
tation. Please note that when the equipment
is in reverse (changeover switch pressed on
the right, Fig. 18 / Item R), it has less power.
•
To clean perimeters and bases, remove the
wide side cover and clean them using the
side brush.
•
Afterwards, rinse the cleaned surface down
with water.
6.4.4 Rough, unsealed paving stones, con-
crete blocks and concreted surfaces
Note: Use only the ULTRA brush to do this (to fi t
the brush, see section 5.5).
Warning! There is a risk of injury from the bristles
of the metal brush – wear safety gloves.
•
Actuate the left side (Fig. 18 / Item V) of the
changeover switch (forward). The equipment
will pull away from you (standard direction of
rotation).
•
In case of certain kinds of stubborn dirt, it can
be helpful to clean using both directions of ro-
tation. Please note that when the equipment
is in reverse (changeover switch pressed on
the right (Fig. 18 / Item R)), it has less power.
Afterwards, rinse the cleaned surface down
with water.
6.4.5 Brushing artifi cial turf
Warning!
•
Use only the SOFT brush to do this (yellow/
green). All other available brushes can dama-
ge the artificial turf.
•
Do not use water - dry-brush only.
•
Brush in a forward direction only (Fig. 18 /
Item V, standard direction of rotation - left side
of the changeover switch actuated).
•
Remove all leaves, rubbish and similar before
starting brushing.
1. Place the SOFT brush evenly on the surface.
2. Set the working height to the one which is
most comfortable for you (see section 5.3).
The splash guard must just clear the ground
on both sides.
Anl_Picobella_SPK9.indb 26 Anl_Picobella_SPK9.indb 26
GB
3. Actuate the left side (Fig. 18 / Item V) of the
changeover switch (standard direction of ro-
tation).
4. Lift the equipment 1-2 centimeters and switch
on the equipment (see section 6.2).
5. Set the desired speed (from slow to fast) (see
section 6.3). Wait until the full speed has been
reached and then place the brush on the ar-
tifi cial turf. The equipment will pull away from
you.
6. To raise the fi bers upright, brush against the
direction of the fi bers of the artifi cial turf once
the desired speed has been reached. Do not
exert any pressure.
7. If required, draw the brush towards you and
let it roll away without pressure.
8. Repeat this movement until the desired result
has been achieved.
7. Cleaning, maintenance and
ordering spare parts
Before putting away or cleaning the equipment,
switch off and remove the battery pack.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment im-
mediately each time after use.
•
Clean the equipment regularly with a damp
cloth. Do not use cleaning agents or solvents;
these may be aggressive to the plastic parts
in the equipment. Ensure that no water can
get into the interior of the equipment. The
ingress of water into an electric power tool
increases the risk of an electric shock.
•
Remove the safety guard and remove any
deposits using a brush.
7.2 Maintenance
There are no other parts inside the equipment
which require maintenance.
- 26 -
24.10.2019 10:36:13 24.10.2019 10:36:13