Publicité
Liens rapides
Stored Energy Hazard: The lift mechanism in the tower is under tension and will move up
rapidly, on its own, as soon as attached equipment is removed. For this reason, DO NOT remove
equipment or make adjustments to lift tension unless the front assembly has been moved to the
highest position on the tower! Failure to follow this instruction may result in serious personal
injury and/or equipment damage!
Riesgo de energía almacenada: El mecanismo de elevación de la torre está bajo tensión y se
moverá rápidamente hacia arriba por sí solo si se retira el equipamiento que hay conectado
al mismo. Es por ello que NO deberá quitar equipamiento ni hacer ajustes en la tensión de
elevación a menos que la estructura delantera se haya movido antes hacia la posición más alta de
la torre. No seguir estas instrucciones podría provocar daños personales y/o materiales graves.
Danger : Le mécanisme d'élévation dans la tour est sous tension et se lève rapidement, tout
seul, dès que le matériel est retiré. Pour cette raison, NE PAS retirer votre matériel ou faire des
ajustemensts à la tension d'élévation à moins que la partie avant n'ait été mise à la position la
plus élevée de la tour ! Risque de blessure corporelle ou d'endommagement matériel en cas de
non respect de cette instruction.
888-24-064-M-02 rev. K • 05/15
WARNING
ADVERTENCIA
AVERTISSEMENT
Neo-Flex Mobile Media Center, UHD
with 90˚ Portrait/Landscape rotation
20"
(510 mm)
User's Guide
Guía del usuario
Manuel de l'utilisateur
-15˚
90˚
+5˚
UHD: 90 - 120 lbs
(41 - 54 kg)
<30 lbs
(15 kg)
<5 lbs
(2.2 kg)
13mm
15mm
14mm
1 of 12
Publicité
Manuels Connexes pour Ergotron Neo-Flex Mobile Media Center UHD
Sommaire des Matières pour Ergotron Neo-Flex Mobile Media Center UHD
- Page 1 Neo-Flex Mobile Media Center, UHD with 90˚ Portrait/Landscape rotation User's Guide Guía del usuario Manuel de l’utilisateur -15˚ 90˚ +5˚ 20" (510 mm) WARNING Stored Energy Hazard: The lift mechanism in the tower is under tension and will move up rapidly, on its own, as soon as attached equipment is removed.
- Page 2 Leg Mounting Hardware M10 x 60mm Leg Cover Mounting Screws M3.5 x 6mm Shelf Mounting Hardware M3 x 37mm TM Mounting Hardware M6x8mm M8 x 14mm M4 x 16mm 400mm Extension Hardware M5 x 16mm Large Display Cart Hardware 5.1(ID) x 10(OD) x 6mm M6x20mm 8.1(ID) x 16(OD) x 6mm M4x20mm...
- Page 3 Shipping Box Caja de embalaje Boîte d'expédition 15mm Leg Mounting Hardware Leg Cover Mounting Screws M3.5 x 6mm CAUTION: DO NOT overtighten fasteners. Overtightening may cause damage to your equipment. Cuidado:: No sobreapriete los tornilllos, pues podría causar un daño al equipo. Attention: ne forcez pas le serrage de la vis, cela pourrait endommager l’écran et/ou les attaches.
- Page 4 Shelf Mounting Hardware M3 x 37mm Shelf Mounting Hardware M3 x 37mm 888-24-064-M-02 rev. K • 05/15 4 of 12...
- Page 5 TM Mounting Hardware TM Mounting Hardware M8 x 14mm 13mm M6x8mm 200 mm 300 mm 400 mm 500 mm 600 mm 600 mm 500 mm 400mm Extension Hardware 400 mm 300 mm M5 x 16mm 200 mm 888-24-064-M-02 rev. K • 05/15 5 of 12...
-
Page 6: Important
FIND APPROPRIATE FASTENERS FOR YOUR DISPLAY: BUSQUE ABRAZADERAS APROPIADAS PARA LA PANTALLA: TROUVEZ LES FIXATIONS APPROPRIÉES À VOTRE ÉCRAN : Large Display Cart Hardware 5.1(ID) x 10(OD) x 6mm M4x20mm 8.1(ID) x 16(OD) x 6mm M6x20mm M4x40mm 5.1(ID) x 10(OD) x 18mm M6x45mm M5x20mm 8.1(ID) x 16(OD) x 24mm... - Page 7 200 mm 300 mm 400 mm 500 mm 600 mm Use fastener chosen from Step 6. Utilice la abrazadera elegida en el paso 6. Utilisez la fi xation choisie au cours de l’étape 6. x < 600mm MINIMUM THREAD ENGAGEMENT LONGITUD MÍNIMA A ENROSCAR ENGAGEMENT MINIMUM DES VIS Tighten screws with at least six, full, 360°...
- Page 8 TM Mounting Hardware M4 x 16mm It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation. Adjustments should move smoothly and easily through the full range of motion and stay where you set it.
- Page 9 TM Mounting Hardware 90˚ 888-24-064-M-02 rev. K • 05/15 9 of 12...
- Page 10 Power Strip Hardware M5x9mm Cable Management Support Hardware Cable Management Support Hardware M5x8mm 888-24-064-M-02 rev. K • 05/15 10 of 12...
- Page 11 Cable Management Support Hardware NOTE: Leave enough slack in cables to allow full range of motion. No deje el cable excesivamente tenso Laisser du mou dans le câble Top Cap Hardware M5x8mm 3.69” 16.8" (93.7 mm) (427 mm) 9.8" (250 mm) 38.4"-58.4"...
- Page 12 LOCK CASTERS when Cart is stationary. Failure to comply with this warning may result in Cart / Stand instability leading to equipment damage or personal injury. © 2015 Ergotron, Inc. All rights reserved. 888-24-064-M-02 rev. K • 05/15 12 of 12...