Q-Connect Q8CC2 Mode D'emploi page 3

When shredding is completed, you can press the designated "push
close" are a on the cover to tilt shut the paper feed slot (FIGURE 4). It
is recommended to have the paper feed slot closed when shredder
is not in use. This will prevent any objects from getting into the feed
slot and accidentally shredded.
*Be sure to not tilt open the cover completely beyond the preset
position, otherwise the ShredSafe™ power cut off feature will be ac-
tivated and the shredder will be inoperable.
I AUto / on :
This setting allows the shredder to be automatically started
by inserting paper into the shred opening. Always feed the
paper in as straight as possible. When the paper has passed
through, the shredder will automatically stop.
o off :
This setting turns off all features of the shredder. For safety
reasons, we recommend that you leave the shredder in the
"Off" position whenever the shredder is unattended or not
in use.
R REV (REVERSE):
In the unlikely event of a paper jam, the reverse setting can
be used to help clear the cutters of paper that has not passed
through. Never attempt to clear a jam by using the reverse
function until you have emptied the wastebasket.
READY : tHE GREEn lED lIGHt InDIC AtES tHE
SHREDDER In "on" AnD READY foR USE.
Never shred large paper clips, window or insulated envelopes, con-
tinuous forms, newsprint, transparencies, laminated documents,
cardboard, any items with adhesives, hard materials or plastic (ex-
cept Credit Cards).
Only shred credit cards by feeding them vertically into the mid-
dle of the entry, releasing when shredding begins. Never feed
more than one credit card at a time.
DO NOT ACTIVATE REVERSE FUNCTION WHILE SHREDDING
CREDIT CARDS.
Overfeeding the shredder: Shredding beyond the specified sheet
capacity can result in extensive damage to the shredder. Overfeed-
ing will strain the machine and quickly wear and break the cutting
blades and internal components.
Overheating with extended use: In the event that the shredder
has shred continuously beyond the maximum running time and
overheating, the unit will automatically shut off. If this happens,
switch the shredder Off for 30 minutes or longer before resuming
normal operation.
MAIntEnAnCE
Warning: Failure to properly maintain your shredder will void
the warranty.
Crosscut shredders require regular oil lubrication for optimal perfor-
mance and extended lifespan. We recommend you oil your shred-
der once a month. Your basic vegetable or cooking oil (nothing
flammable or petroleum based) can be drizzled onto a few sheets
3
of paper and fed into the shredder.
ONLY USE NON-AEROLSOL VEGETABLE BASED OILS TO OIL YOUR
CUTTERS. DO NOT SPRAY OR KEEP ANY AEROSOL PRODUCTS IN
OR AROUND THE SHREDDER. DO NOT USE CANNED AIR.
Be sure to periodically empty the wastebasket to avoid over-
loading and damaging the cutting mechanism.
ClEAnInG:
• ALWAYS UNPLUG THE SHREDDER BEFORE CLEANING!
• Only clean the shredder by carefully wiping the unit with a dry
soft cloth or towel.
• Do not clean or immerse shredder in water. Having the unit wet
may result in damage or malfunction to the electrical compo-
nents. If the shredder happens to get wet, be sure to completely
dry the unit immediately with a cloth or towel.
• Never use anything flammable to clean the shredder. This may
result in serious injury or damage to the product.
tRoUBlESHootInG
If there is a problem with your shredder, check below for the symp-
toms and steps to resolve. If you continue to have problems, contact
customer support at our Service Center. DO NOT ATTEMPT TO RE-
PAIR BY OPENING THE SHREDDER HEAD. This will completely
void the product warranty.
tHE SHREDDER DoES not WoRk At All.
a) Make sure the unit is plugged in and that the outlet it is plugged
into is in good working order.
b) Overheating with extended use: In the event that the shred-
der has shred continuously beyond the maximum running time
and overheating, the unit will automatically shut off. If this hap-
pens, switch the shredder Off for 30 minutes or longer before
resuming normal operation.
c) Make sure the head unit portion of the shredder is correctly seat-
ed onto the included waste-
basket, with all the words and
icons facing towards you. The
head unit is particularly de-
signed to work only with the
integrated wastebasket.
Shredders are equipped with
a safety interlocking mechanism, which prevents the shredder
from working when the head unit is lifted, removed, or acciden-
tally knocked over. On the back center edge of the shredder
head, next to the power cord, is a "curved flap-like shape" that
MUST FIT OVER THE OUTSIDE matching ridge of the wastebas-
ket. The shredder will not function unless the head unit is prop-
erly mounted as pictured.
d) Be sure to not tilt the cover completely open beyond the
preset position, otherwise the ShredSafe™ power cut off
feature will be activated and the shredder will be inoper-
able.
e) If using a plastic bag to line the wastebasket, please remove it
since this may be the cause of the shredder to not operate prop-
erly.
f ) The activation sensor of the shredder is located near the center
of the feed slot. Be sure to feed directly into the center area to ac-
t
W W W . Q - C O N N E C T . C O M