Preparing To Charge - TecMate Optimate lithium LFP Select TM270 Mode D'emploi

SAVE THESE INSTRUCTIONS.
AUTOMATIC CHARGER ONLY FOR 12.8V / 16V LiFePO
PHOSPHATE / LITHIUM IRON PHOSPHATE) BATTERIES.
DO NOT USE FOR NiCd, NiMH, Lead-Acid or any other type of Li-Ion or
NON-RECHARGEABLE BATTERIES.
*IEC62133 - Safety requirements for portable sealed secondary cells containing alkaline or other
non acid electrolytes and for batteries made from them, for use in portable applications.
1. CAUTION : DO NOT CONNECT TO GROUND.
2. For indoor use only. Do not expose charger to rain or snow.
3. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric
shock,or injury to persons.
4. To reduce risk of damage to electric plug and cord,pull by plug rather than cord when disconnecting charger.
5. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of
fire and electric shock.If extension cord must be used make sure that :
a) pins on plug of extension cord are the same number, size and shape as those of plug on charger, b) the extension cord is
property wired and in good electrical condition,and c) the conductor wire size is large enough for the AC ampere rating of
the charger as specified in the table below.
Equal to or greater than
than
6. Do not operate charger with damaged cord or plug - replace the cord or plug immediately.
7. Do not operate charger if it has received a sharp blow, been dropped,or otherwise damaged in any way; take it to a
qualified serviceman.
8. Do not disassemble charger; take it to a qualified serviceman when service or repair is required.
Incorrect reassembly may result in a risk of electric shock or fire.
9. To reduce risk of electric shock, unplug the charger from outlet before attempting any maintenance or cleaning.
Turning off controls will not reduce this risk.Clean only with slightly moist,not wet, cloth.Do not use solvents.
10. warning - risk of explosive gases. a) working in vicinity of a lead-acid battery is dangerous. Batteries generate explosive
gases during normal battery operation. for this reason, it is of utmost importance that you follow the instructions each time
you use the charger. b) To reduce risk of battery explosion,follow these instructions and those published by the battery
manufacturer and manufacturer of any equipment you intend to use in vicinity of the battery. Review cautionary marking on
these products and on engine.
11. PERSONAL PRECAUTIONS.
a) Someone should be within range of your voice OR close enough to come to your aid when you work near a battery. b)
Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing or eyes. c) Wear complete eye
protection and clothing protection. Avoid touching eyes while working near a battery. d) If battery acid contacts or enters
eye, flood eye with cold running water for at least 10 minutes and get medical attention immediately. If battery acid contacts
skin or clothing, wash immediately with soap & water. If acid enters an eye , immediately flood eye with running cold water
for at least 10 minutes & get medical attention immediately. e) NEVER smoke or allow a spark or flame in vicinity of battery
or engine. f) Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or short-circuit battery or
other electrical part that may cause explosion. g) Remove personal metal items such as rings, bracelets ,necklaces , and
watches when working with a battery. A battery can produce a short-circuit current high enough to weld a ring or the like to
metal, causing a severe burn. i) NEVER charge a frozen battery.

12. PREPARING TO CHARGE

a) If necessary to remove battery from vehicle to charge,always remove grounded terminal from battery first.
IMPORTANT SAFETY
INSTRUCTIONS FOR CANADA & USA
AC INPUT RATING IN AMPERES
2A
(LITHIUM FERROUS
4
LENGTH OF
But less CORD, FEET (m)
3A 25 (17.6)
50 (15.2)
100 (30.5)
AWG
SIZE OF
CORD
18
18
14
1