Hrm-Run ™ Instructions - Garmin HRM-Run Mode D'emploi

HRM-Run
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Putting On the Heart Rate Monitor
You should wear the heart rate monitor directly on your skin, just
below your sternum. It should be snug enough to stay in place
during your activity.
1 If necessary, attach the strap extender to the heart rate
monitor.
2
Wet the electrodes on the back of the heart rate monitor to
create a strong connection between your chest and the
transmitter.
3
Wear the heart rate monitor with the Garmin
right-side up.
The loop and hook
side.
4 Wrap the heart rate monitor around your chest, and connect
the strap hook to the loop.
NOTE: Make sure the care tag does not fold over.
After you put on the heart rate monitor, it is active and sending
data.
Pairing the Heart Rate Monitor with Your
Device
Before you can pair the heart rate monitor with your device, you
must put on the heart rate monitor.
Pairing is the connecting of ANT+
heart rate monitor, with a Garmin ANT+ compatible device.
NOTE: The pairing instructions differ for each Garmin
compatible device. See your owner's manual.
• For most Garmin compatible devices, bring the device within
3 m of the heart rate monitor and use the device menu to pair
manually.
• For some Garmin compatible devices, bring the device within
1 cm of the heart rate monitor to pair automatically.
TIP: Stay 10 m away from other ANT+ sensors while pairing.
After you pair the first time, your Garmin compatible device
automatically recognizes the heart rate monitor each time it is
activated.
Running Dynamics
You can use your compatible Garmin device paired with the
HRM-Run accessory to provide real-time feedback about your
™
running form. If your Garmin device was packaged with the
HRM-Run accessory, the devices are already paired.
2
™ Instructions
WARNING
® logo facing
connection should be on your right
® wireless sensors, like your
The HRM-Run accessory has an accelerometer in the module
that measures torso movement in order to calculate six running
metrics.
NOTE: The HRM-Run accessory is compatible with several
ANT+ fitness products and can display heart rate data when
paired. The running dynamics features are available on only
some Garmin devices.
Cadence: Cadence is the number of steps per minute. It
displays the total steps (right and left combined).
Vertical oscillation: Vertical oscillation is your bounce while
running. It displays the vertical motion of your torso,
measured in centimeters for each step.
Ground contact time: Ground contact time is the amount of
time in each step that you spend on the ground while
running. It is measured in milliseconds.
NOTE: Ground contact time is not available while walking.
Ground contact time balance: Ground contact time balance
displays the left/right balance of your ground contact time
while running. It displays a percentage. For example, 47%
Left - 53% Right.
Stride length: Stride length is the length of your stride from one
footfall to the next. It is measured in meters.
Vertical ratio: Vertical ratio displays your vertical oscillation as a
percentage of your stride length. A lower ratio typically
indicates better running form.
Troubleshooting
Tips for Erratic Heart Rate Data
If the heart rate data is erratic or does not appear, you can try
these tips.
• Reapply water to the electrodes and contact patches (if
applicable).
• Tighten the strap on your chest.
• Warm up for 5 to 10 minutes.
• Follow the care instructions
Monitor, page 3).
• Wear a cotton shirt or thoroughly wet both sides of the strap.
Synthetic fabrics that rub or flap against the heart rate
monitor can create static electricity that interferes with heart
rate signals.
• Move away from sources that can interfere with your heart
rate monitor.
Sources of interference may include strong electromagnetic
fields, some 2.4 GHz wireless sensors, high-voltage power
lines, electric motors, ovens, microwave ovens, 2.4 GHz
cordless phones, and wireless LAN access points.
Tips for Missing Running Dynamics Data
If running dynamics data does not appear, you can try these
tips.
• Make sure you have the HRM-Run accessory.
Accessories with running dynamics have
module.
• Make sure your Garmin device supports running dynamics.
For more information, go to www.garmin.com/intosports.
• Pair the HRM-Run accessory with your Garmin device again,
according to the instructions.
• If the running dynamics data display shows only zeros, make
sure the heart rate monitor is worn right-side up.
NOTE: Ground contact time appears only while running. It is
not calculated while walking.
Replacing the Heart Rate Monitor Battery
1
Remove the sleeve from the heart rate monitor module.
(Caring for the Heart Rate
on the front of the
Installation Instructions