Applications; Conformity And Approval; Setting Up The Transmitter; Connecting The Transmitter - Monacor International JTS SIEM-2/5 Mode D'emploi

1 if one of the units is visibly damaged,
2 if a defect might have occurred after a unit
was dropped or suffered a similar accident,
3 if malfunctions occur
In any case the units must be repaired by skilled
personnel
•
For cleaning only use a dry, soft cloth; never use
water or chemicals
•
No guarantee claims for the units and no liability
for any resulting personal damage or material
damage will be accepted if the units are used for
other purposes than originally intended, if they
are not correctly connected or operated, or if
they are not repaired in an expert way
If the units are to be put out of operation
definitely, dispose of the units in accord­
ance with local regulations
3

Applications

The set SIEM­2 / 5 is a wireless mono audio trans­
mission system designed for stage monitoring
(in­ear monitoring); it is also suited for various other
mobile audio signal transmissions, e g wireless
command or control transmission The set includes
the transmitter SIEM­2T and the receiver SIEM­2 / R5
with the earphones IE­1 To extend the system,
the receiver and the earphones are also available
separately Thus, you will be able to operate any
number of receivers with a single transmitter

3.1 Conformity and approval

Herewith, MONACOR INTERNATIONAL declare that
the products SIEM­2 / 5 and SIEM­2 / R5 comply with
the directive 2014 / 53 / EU The EU declarations of
conformity are available on the Internet:
www jts­europe com
Restrictions or requirements apply in the fol-
lowing countries:
CZ
IT
The regulations of the country where the prod­
ucts are operated must always be observed Prior
to operating the products, please contact the
MONACOR subsidiary or the corresponding au­
thorities of the respective country Links to the
national authorities can be found via the following
Internet address:
EL FI FR
LT MT PL
www cept org
t ECC
t Topics
t Other spectrum topics: SRD Regulations and
indicative list of equipment sub­classes
t EFIS and National Frequency Tables
4 Setting the System into Operation

4.1 Setting up the transmitter

To obtain the best transmission quality, place the
transmitter at the height of the receiver (approx
1 m above the ground) Make sure that there are no
obstacles between the transmitter and the receiver
Keep a distance of approx 1 m between the trans­
mitter and lateral walls
For installing the transmitter into a rack
(482 mm / 19"), use the mounting frame DR­900SET
The frame allows installation of two transmitters
After setting up, place the transmitting an­
tenna (7) in a vertical position

4.2 Connecting the transmitter

1) Connect the signal source(s), e g microphone,
output of a mixer, to the jacks MIC / LINE (1) The
jacks are designed for balanced signals If there
is only an unbalanced signal at the output of
the signal source, feed this signal to the input
jack via a 6 3 mm mono plug
2) To route the input signals from the jacks MIC /
LINE 1 and 2 to another unit (e g amplifier,
second transmitter, recorder), these signals are
available at the jacks LOOP OUT (8)
3) For power supply, connect the power supply
unit provided to the jack "⎓DC 12~18V" (11),
then connect it to a mains socket (230 V / 50 Hz)
To prevent accidental disconnection of the
plug from the jack "⎓DC 12~18V", wrap the
cable around the hook (9) from below for strain
relief
4.3 Power supply of the receiver
For power supply, two (rechargeable) batteries of
size AA are required
•
Only insert two batteries of the same type and
always replace both of them
•
If the receiver is not in use for a longer period
of time, always remove the batteries to prevent
damage due to battery leakage
9