Steba LB 6 Mode D'emploi page 9

Power on
Connect to power, the buzzer beeps, humidifier enters standby mode. Turning it on
by pressing the "On/Off" switch, this regulates to the standard setting.
(Middle humidifying capacity, no timer, 70% RH and lights of the tank being turned
on.)
Light
Press the "light" switch in order to switch the light on or off.
Adjusting the temperature of the mist
Press the "cooler/warmer" switch to change the temperature of mist.
Humidity and Timer
Presses "HUM/SPEED" switch to change from humidity setting to timer setting and
vice versa. Once it has been changed to the respective mode, the sign would sparkle.
Adjust the rate of humidity and timer by pressing the "+" or "-" switch.
1 Humidity setting
1.1 Presses "HUM/SPEED" switch, humidity sign would now sparkle.
1.2 Presses "+" and "-" to adjust the humidity. From the minimum 30% RH to
the maximum 70% RH.
1.3 It would be effective right after the humidity has been adjusted.
NOTE: The humidifier would stop emitting mist once it reaches the desired humidity
and would only emit mist when the humidity of the area drops to around 5% RH of
the set humidity.
1.4 When the humidity sign reaches 70% RH, keep on pressing "+", the humidi-
fier would switch to the continuous mode, which would be represented by "CO". In
this mode, the emitting of mist would not be affected by the humidity in the room
and would work continuously.
2 Timer setting
2.1 Presses "HUM/SPEED" switch twice, the timer sign would then sparkle.
2.2 Presses "+" and "-" to adjust the timer. From 0 hour to 12 hours.
2.3 The timer would now start to count down. When it reaches 0 hour, it would
stop immediately and enter the standby mode.
2.4 If the timer in set with 0 hour, the humidifier would work continuously.
Note: Normal display would be jumping from environment's humidity and timer.
Changing the humidifying capacity.
When there are no special settings, by pressing only "+" or "-" could adjust the humi-
difying capacity.
* Low capacity: Mist added to air would exceed 100 ml, only the low capacity light
would be on.
* Middle capacity: Mist added to air would exceed 200 ml, both the low and middle
capacity light would be on.
* High capacity: Mist added to air would exceed 300 ml, all the low, middle and high
capacity light would be on.
16
Water short indicator
1 Once the tank runs out of water, within a few seconds the humidifier would enter
the protection mode. The humidifier would then keep on "beeping" for around ten
times. Apart from the sparkles at the mist indicator, other signs would be off.
2 In this mode, only "On / Off" switch could be used to switch off the humidifier.
3 Refill the tank and put it back to the humidifier. Wait for around 10 seconds, the
humidifier would resume working.
Shut-down
1 Presses "On / Off" switch to turn off the humidifier.
2 If you choose not to unplug the humidifier, all settings except the timer would be
saved. Once it has been unplugged, all the settings would reset.
Reminder:
∙ This ultrasonic humidifier uses a piece of metal diaphragm to vibrate at an ultraso-
nic frequency creates water droplets that silently exit the humidifier in the form of
a cool fog.
∙ The "gurgling" sound is normal, as water would go through the filter to the gutter.
∙ The intensity of the mist would be affect by the relative humidity, temperature of
the area. It would be harder to generate mist if it is cold and wet.
∙ The water used should be between 4°C to 50°C and should be clean tap water or
distilled water.
MAINTENANCE & WASH
∙ Please unplug the appliance before washing.
∙ Wash the water tank every two or three weeks.
Maintenance for the filter
∙ Filter is consists of core box, ceramic balls yellow water softening particles and
cover.
∙ The yellow water softening particles reduces the dissolved calcium, magnesium,
and to some degree manganese and ferrous iron ion concentration in hard water.
∙ The water filter should be cleaned every one or two weeks according to water qua-
lity. It is better to be cleaned more frequently.
Steps of cleaning:
1. Take off the tank, unscrew the cover and take out the tank and the filter.
2. Immerse the filter into clean water. Clean the impurities on the non-woven fabric
and wash the water filter.
3. Fix the water filter.
Please take the water filter out and keep it dry if the appliance is going to be left
unused for a long time.
Caution: Do not disassemble water filter. Please replace it every one or two years
Waterfilter
17