Peg-Perego book plus Notice D'emploi page 14

ensure that the base is connected properly.
2 FITTING THE WHEELS: Slot the uprights into
the rear wheel crosspiece (fig_a), ensuring
that it is facing the right way, then push the
rear wheels on and make sure that they click
into place (fig_b).
3 FITTING THE BASKET: Press the buttons under the
basket tube (fig_a) and remove it (fig_b). Thread
the tube through the basket fabric, making sure
that the springs are facing down (fig_c), and click
it back into place. Attach the basket to the two
buttons at the front (fig_d) and
4 fasten the eyelets at the rear onto the buttons
as shown in the figure, with the upper one
going from the top towards the bottom
(fig_e) and the lower one going from the
inside towards the outside (fig_f ).
5 FIXED OR SWIVELING FRONT WHEELS: Lift the
levers to prevent the wheels from swiveling
(fig_a) and lower them to allow the wheels to
swivel (fig_b). On uneven surfaces, the wheels
should be set to their fixed position.
6 BRAKE: Press the lever down to apply the brake
on the chassis and lift it to release the brake.
7 ADJUSTABLE HANDLEBAR: To adjust the
height of the handlebar, press both of the
side buttons at the same time (fig_a) and
swing it into the desired position (fig_b), then
release the buttons.
8 DRINK HOLDER: Push the drink holder firmly
onto the clip (fig_a). The drink holder can be
attached to either side of the chassis.
9 ATTACHING THE SEAT ONTO THE CHASSIS:
the reversible seat can be attached onto
the chassis to face mum or to face outwards
(fig_a). Position centrally on the chassis and
press down with both hands until it double
clicks into place. To make sure that it is
properly attached, take hold of the seat via
the front bar and pull it up.
1 0 REMOVING THE SEAT FROM THE CHASSIS:
Hold down the two round buttons on the
sides of the seat (fig_a), press the two levers
under the armrests (fig_b) and pull up the
seat (fig_c) until it is released. The seat can be
removed from and re-attached to the chassis
when there is a child in it.
1 1 FRONT BAR: Before attaching the front bar,
press the buttons on the sides of the armrests
and remove the caps (fig_a). To attach the front
bar, guide the connections into the armrests
and push towards the seat until they click into
place (fig_b). To remove the front bar, press
the two buttons and pull it out (fig_c). To make
it easier for the child to get in and out, it is
possible to open the front bar on one side only.
If you wish to use the stroller without the front
bar, put the caps back in the armrests.
1 2 BACKREST: to recline the backrest lift
the lever (fig_a) and choose one of the 4
positions (fig_b).
1 3 FOOTREST: to lower the footrest push the two
levers downwards and then push the footrest
downwards (fig_a); to raise the footrest lift it
upwards (fig_b).
1 4 FIVE POINT SAFETY HARNESS: To fasten it,
push the two waist strap buckles (with the
shoulder straps attached – arrow_a) into
the leg divider until they click into place
(arrow_b). To unfasten it, press the round
button in the centre of the buckle (arrow_c)
and pull the waist straps out (arrow_d).
1 5 To tighten the waist strap, pull on both sides
in the direction of the arrow (arrow_a). To
loosen it, move it in the opposite direction.
1 6 To adjust the height of the safety harnesses,
release the two buckles on the rear of the
backrest.
Pull the shoulder straps towards you (arrow_a)
until the buckles are released and insert them
in the backrest loops (arrow_b). Remove the
shoulder straps from the sack (arrow_c) and
insert them in the most appropriate loop
(arrow_d), then re-attach the two buckles on the
rear of the backrest (arrow_e) The buckles are
securely attached when a click is heard (fig_f).
1 7 HOOD: WARNING. Ensure the buttons are
fastened on the rear of the backrest. If this
is not the case, fasten them now (fig_a). To
open the hood, pull it towards you; to close
the hood, push it backwards. The hood may
only be used as a parasol if the backrest
is not fully reclined. In this case, open the
double slider zipper (fig_b) and unfasten the
hood buttons on the rear of the backrest.
The hood comes with a loop from which to
dangle baby's favorite toy (fig_c).
1 8 COVER: put on the cover, and fasten it
underneath (fig_a) and on the sides of the
footboard. For the baby carriage version, move
the footboard up and place the cover over the
front bar (fig_b), fastening it to the buttons of
the hood (fig_c). For the stroller version, move
the footboard down, insert the cover underneath
the front bar (fig_d) and fix it in place.
19 BABY SAFE: pull the Baby Safe system out
from under the leg rest (fig_a), attach it to the
seat (fig_b), fit the front bar (fig_c), unbutton
the fabric covering at the side and then
attach the Baby Safe system to the sides of
the armrests (fig_d). A fitted Baby Safe system
is shown in Figure E.
2 0 RAIN CANOPY: position the rain canopy on
the stroller (fig_a) and insert the two lateral
loops over the hood buttons (fig_b).
2 1 Secure the rain canopy by attaching the
elastic loop to the rear uprights (fig_a) or to
the front uprights (fig_b), according to the
seat position.
2 2 FOLDING UP: to fold up the seat press the
outer sides towards the inside (fig_a) and fix
in place with the fastener (fig_b).
- 14 -