Table des Matières
Publicité
Source language: German
EU Declaration of conformity
Explication of warning symbols
Safety instructions
Intended use
Unpacking
Useful information
Setting up
Commissioning
Maintenance and cleaning
Accessories
Troubleshooting
Technical data
Warranty
EU Declaration of conformity
We declare under our sole responsibility that this product corresponds to the directives 2014/35/EU, 2006/42/EC, 2014/30/EU
and 2011/65/EU and conforms with the following standards or normative documents: EN 61010-1, EN 61326-1, EN 60529
and EN ISO 12100.
A copy of the complete EU Declaration of Conformity can be requested at sales@ika.com.
Explication of warning symbols
General hazard
This symbol identifies information that is of vital importance for protecting your health
DANGER
and safety. Disregarding this information may lead to health impairment and injuries.
This symbol identifies information that is of importance for the technically correct func-
WARNING
tioning of the system. Disregarding this information may result in damage to the instrument
or to system components.
This symbol indicates information which is important for proper use and ensuring that the
CAUTION
operations of the instrument are performed efficiently and for using the instrument.
Failure to observe this information may result in inaccurate results.
Contents
EN
• Read the operating instructions fully before starting up
and follow the safety instructions.
• Keep the operating instructions in a place where they can
be accessed by everyone.
Page
• Ensure that only trained staff work with the instrument.
• Follow the safety instructions, guidelines, occupational
12
health and safety and accident prevention regulations.
12
• Wear your personal protective equipment in accordance
13
with the hazard category of the medium to be processed.
14
There may be risk from glass breakage.
14
14
15
DANGER
16
16
ing parts as internal parts are moving at a very high speed.
17
18
• Always ensure that front cover is attached before starting
19
up the device.
19
• Do not lift the pump if top motor cover is not tighten
properly.
• Do not switch the pump on in the vertical position as it is
not stable in this position.
• Always operate the pump in the horizontal position.
• Place the pump on a stable and even surface before
switching the power on.
DANGER
ical materials can be hazardous to user. Make sure con-
nections are tight and free from leaks when dealing with
such media.
• The pump system is not designed to be explosion proof.
Ensure that the temperature of the medium being evacu-
ated with the vacuum is below the ignition temperature.
Attention must be paid to temperature rise of medium
while being evacuated.
• Do not operate the appliance with hazardous substances or
under water.
• Tasks with the device must only be performed when op-
eration is monitored.
• There may be electrostatic discharges between the me-
dium and the drive which could pose a direct danger.
12
Safety Instructions
• Safe operation is only guaranteed with the accessories de-
scribed in the "Accessories" chapter.
• Only authorized personnel are allowed to disassemble the
appliance.
• The device can only be disconnected from the power sup-
ply network by pulling out the mains plug or the connec-
tor plug.
• The socket for the mains cord must be easily accessible.
• Position the positive pressure outlet of the vacuum pump
under a fume hood.
• Refer to the operating instructions for the equipment this
Do not operate pump when front
vacuum pump is connected to, e.g. rotary evaporator.
cover is open. This may lead to seri-
• The motor is shut down by a thermal cutout safety switch
ous injury if hand is caught in mov-
in the winding.
- Manual reset is necessary. Switch off device or isolate the
equipment from mains. Wait approx. five minutes before
restarting the device.
- Use device in conditions specified in "Technical Data"
section.
• Do not use pump to generate pressure.
• Maximum pressure at gas inlet or outlet should not ex-
ceed 1 bar.
• Use solenoid/check valves if there are several load devic-
es.
• Use only flexible hoses.
For protection of the equipment
• The voltage stated on the type plate must correspond to
the mains voltage.
• Socket must be earthed (protective ground contact).
• Removable parts must be refitted to the appliance to pre-
vent the infiltration of foreign objects, liquids etc.
• Protect the appliance and accessories from bumps and im-
pacts.
• The instrument may only be opened by experts.
• Do not cover the ventilation slots of the instrument in
order to ensure adequate cooling of the instrument.
Inhalation of or contact with media
• Use only genuine spare parts for maintenance to ensure
such as poisonous liquids, gases,
good working condition of the instrument.
spray mist, vapours, dusts or biolog-
• Pay attention to water condensation in and outside of the
instrument. Allow instrument to warm up if brought in from
a cold environment.
• Do not use the pump to evacuate any solid substance as
this will damage the diaphragm and the internal parts of the
pump.
• Do not use the pump to evacuate liquids as it will reduce
the lifespan of the diaphragm and cause leakage.
• Ensure that any substances to be used with the instru-
ment are compatible to the materials of the "Wetted
parts" of the device; see section "Technical data".
13
Publicité
Table des Matières
