Table des Matières
Publicité
MultiFlow Quick Start
Pos : 11 /T echD OC/Seni ng/09-MultiFl ow/D OK- 392_Kurzanlei tung Fahrer /| 1---> Quic k Start @ 2\mod_1338466079858_19.doc x @ 40302 @ 1 @ 1
2 Quick Start
Pos : 12.1 /T echD OC/Seni ng/09-MultiFl ow/D OK-392_Kurzanleitung Fahrer /| H01--->Die wic htigsten Tas ten @ 3\mod_1355824819247_19.doc x @ 68914 @ @ 1
1
.
The main keys
Pos : 12.2 /T echD OC/Seni ng/09-MultiFl ow/D OK-392_Kurzanleitung Fahrer /Q01 - Die wichtigsten T asten @ 3\mod_1355824945576_19.doc x @ 69213 @ @ 1
As a rule, the following functions are assigned to the below keys:
<Start>
<Stop>
<Print>
<Enter>
Pos : 12.3 /T echD OC/Seni ng/09-MultiFl ow/D OK-392_Kurzanleitung Fahrer /| H02---> Abgabe @ 3\mod_1355824823419_19.doc x @ 68937 @ @ 1
2
.
Discharge
Pos : 12.4 /T echD OC/Seni ng/09-MultiFl ow/D OK-392_Kurzanleitung Fahrer /Q02 - Abgabe @ 3\mod_1355824953669_19.doc x @ 69259 @ @ 1
This manual only regards operation of the MultiFlow. Of course, all other conditions concerning
the discharge of product have to be met as well.
Switch on the MultiFlow.
The MultiFlow runs a self-test after which it is
ready for discharge.
Press the <Start> key to start the discharge.
In case hose selection is not available, pass on
to "Delivery preset".
Pos : 12.5 /T echD OC/Seni ng/09-MultiFl ow/D OK-392_Kurzanleitung Fahrer /| H03---> Abgabe- Vor wahl @ 3\mod_1355824827732_19.doc x @ 68960 @ @ 1
3
.
Delivery preset
Pos : 12.6 /T echD OC/Seni ng/09-MultiFl ow/D OK-392_Kurzanleitung Fahrer /Q03 - Abgabe- Vor wahl @ 3\mod_1355824961732_19.doc x @ 69305 @ @ 1
Now the delivery preset menu appears. The
selection made before is displayed and the
selected hose is marked.
For MultiFlow units with residue removal control:
after entering all the preset values by pressing
the <START> key, the MultiFlow checks
whether a product change has taken place
between diesel and heating oil / heating oil with
additives. If this is the case, a corresponding
message is shown regarding the necessity of
residue removal.
6
Start discharge
a)
Stop or terminate discharge
b)
Quit an entry without saving the data
a)
Switch to the report selection menu
b)
Confirm and save entered values
Go to the next possible entry
MN F09 012 US DOK-392E Issue/Rev. 2.01 (01/13)
F A S e n i n g M U L T I F L O W
S e l e c t P r o d u c t a n d
V o l u m e w i t h < S T A R T >
P r i n t R e p o r t s
w i t h
C u s t o m i z e S e t t i n g s
w i t h
R e a d y
S e l f t e s t
S e a l
V e r s i o n 5 . 0 3 [ 5 . 1 3 ] U K
S e a l
L o a d
D e l i v e r y P r e s e t
C u s t o m e r I D : 0 0 0 0 0 0
- - - - - - - - - - - - - - - - - - -
P r o d u c t C o d e : > 1 1 <
H e a t i n g O i l
A m o u n t : 1 0 0 0
P r i c e p e r
w . V A T
- - - - - - - - - - - - - - - - - - -
W e t h o s e 2
C o n t i n u e w i t h E N T E R
C N o :
- - -
C l e a r
®
Sening
is a registered trademark of FMC Technologies
< P R I N T >
< F 3 >
O K
O K
M e n u
l
1 0 0
$
8 7 . 6 5
1 1
- - -
Publicité
Chapitres
Table des Matières
