Warning Messages - Sony VPL-HS20 Mode D'emploi

"Memory Stick"
The "Memory Stick"
cannot be inserted into
the "Memory Stick"
slot.
A still picture in the
"Memory Stick"
cannot be rotated or
deleted.
The "Memory Stick"
cannot be formatted.
The thumbnails are not
displayed.
The still pictures files
in the JPEG format
stored in a "Memory
Stick" cannot be
displayed.
The movie picture files
in the MPEG1 format
stored in a "Memory
Stick" cannot be
displayed.
Indicators
The LAMP/COVER or TEMP/FAN indicator on the
control panel lights up or flashes if there is any trouble
with your projector.
LAMP/COVER Indicator
LAMP/
COVER
LAMP/COVER
flashes.
LAMP/COVER
lights up.
TEMP/FAN
flashes.
60
Troubleshooting
GB
c Insert the "Memory Stick" with
the arrow mark pointing toward
the "Memory Stick" slot of the
projector. (1 page 40)
c Release the lock for the write-
protect tab on the "Memory
Stick". (1 page 39)
c Release the protect in the index
screen. (1 page 50)
c Release the lock for the write-
protect tab on the "Memory
Stick". (1 page 39)
c The "Memory Stick" is broken.
Use another "Memory Stick".
c The pictures are the JPEG
format but not DCF-compatible.
Use the DCF-compatible
pictures.
c Set "Filter" in the "Option"
menu to "Still" or "Off."
c Set "Filter" in the "Option"
menu to "Movie" or "Off."
TEMP/FAN Indicator
TEMP/ POWER ON/
FAN SAVING STANDBY
c Attach the lamp cover or the air filter
cover securely. (1 pages 62 and 63)
c The lamp has reached the end of its
life. Replace the lamp. ((1 page 62))
c The lamp becomes a high temperature.
Wait for one minute to cool down the
lamp and turn on the power again. (1
page 27)
c The fan is broken. Consult with
qualified Sony personnel.
TEMP/FAN c The internal temperature is unusually
lights up. high. Check to see if nothing is
blocking the ventilation holes
whether or not the projector is being
used at high altitudes .
c The electrical system breaks down.
LAMP/COVER
and TEMP/FAN Consult with qualified Sony
light up. personnel.

Warning messages

Use the list below to check the meaning of the
messages displayed on the screen.
c Turn off the power.
High temp.!
c Check to see if nothing is blocking the
Lamp off in 1
min. ventilation holes.
c Input a signal that is within the
Frequency is
out of range! acceptable range of the frequency.
c Set the output signal on an external
monitor of the connected computer to
SVGA.
c Set "Input-A Signal Sel." in the SET
SETTING
Please check c Set "Input-A Signal Sel." in the SET
Input-A Signal SETTING
Sel. when RGB signal is input from the
computer. (1 page 34)
c Set "DVI Signal Sel." in the SET
Please check
DVI Signal Sel. SETTING
when RGB signal is input from the
computer.(1 page 34)
Note
Before you change the "DVI Signal Sel." setting,
disconnect the DVI cable and turn off the digital
tuner, etc.
c It is time to replace the lamp. Replace
Please replace
the LAMP. the lamp. (1 page 62)
c It is time to replace the air filter. Replace
Please replace
the filter. the air filter. (1 page 63)
c When using the projector at an altitude
High temp.!
Probably use in of 1,500 m or higher: select "Yes" to set
high altitude. to "High Altitude Mode". (1 page 35)
c If this message is displayed when
Switch to high
altitude mode using the projector at an altitude of
on? Yes: O/ less than 1,500 m: check to see if
No: o nothing is blocking the ventilation
holes.
c The iris is damaged.
Iris unit doesn't
work. c Consult with qualified Sony Personnel.
or
menu to "Computer".
menu to "Computer"
menu to "Computer"