Bosch AXT 22 D Notice Originale page 19

Assembly
For Your Safety
Warning! Switch off, remove plug from mains before
adjusting, cleaning or if cable is cut, damaged or entan-
gled.
Observe correct mains voltage: The voltage of the power
source must agree with the voltage specified on the name-
plate of the unit. Equipment marked with 230 V can also be
connected to 220 V or 240 V.
The circuit must at least be protected as follows:
AXT 22 D/25 D/23 TC/25 TC/2550 TC= 13 A
An extension cable with a cross section that is too small caus-
es a distinct reduction in the performance capabilities of the
machine. For cables to 25 m in length, a cross section of at
2
least 3 x 1.5 mm is required, for cables more than 25 m in
length, the cross section must be at least 2.5 mm
WARNING! Inadequate extension cables can be dan-
gerous. Extension cable, plug and socket must be of
watertight construction and intended for outdoor use.
Cable connections should be kept dry and off the ground.
It is recommended for increased electrical safety to use a Residu-
al Current Device (RCD) with a tripping current of not more than
30 mA. Always check your RCD every time you use it.
If the supply cord is damaged, it must be replaced by a Bosch
Service Centre.
When using cable drums, these must be completely unreeled.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Assembly
Remove the machine from the package. (see figures A–D).
Assemble the chute (see figures E–F)
Lift back blade cover plate 13.
Hook in chute assembly 8 to the garden product, and
then release the blade cover plate 13.
Press the chute 8 down and turn red clamping knob 9
fully clockwise to lock the chute 8 in place, approxi-
mately 5x full turns of the clamping knob 9 are re-
quired.
Bosch Power Tools
Operation
Starting Operation (see figure G)
Always place the machine on firm level ground. During
operation, do not tilt or move.
The motor will coast after switching off!
Remove earth from roots. Foreign material such as stones,
glass, metals, fabrics or plastics must not enter the chute as-
sembly 8. Otherwise this could damage the cutting roller 16.
The chute assembly 8 must be empty.
Starting
Press green button 4.
Stopping
Press red STOP button 5.
Wait for 2 seconds before restarting the machine.
2
.
Restarting Protection
A mains failure causes machine to switch off. The machine
cannot restart on its own when the power returns.
Return Motion
Press and hold the yellow button 6 to reverse the feed.
The cutting roller 16 runs backward and frees jammed mate-
rial.
Overload Protection
Overloading (e. g. blocking of the cutting roller 16) causes the
machine to stop after a few seconds, that time a beep is audible.
Press red STOP button to clear the error. After blocking the
tool can start in reverse direction.
Press and hold the yellow button 6 to reverse the cutter to un-
block.
In case of starting in the same direction the tool won't start
and beeps.
If the blockage cannot be cleared the pressure plate 15 will
need to be moved away from the cutter.
The adjustment knob 10 will need to be turned a counter-
clockwise direction a small amount until the "jammed" mate-
rial is clear. The pressure plate 15 will need adjustment (see
"Pressure Plate Adjustment (see figure H)").
Working Advice
Wear eye protection, hearing protection and safety
gloves at all times while operating the machine.
Always check before use that the collection box and
chute assembly are fitted correctly.
The machine is fitted with sensors, unless the collection box
11 is fitted correctly and the chute assembly 8 is correctly po-
sitioned, the machine will not start and the buzzer beeps (on
AXT 23 TC/25 TC/2550 TC also the 2 LEDs 14 flash).
Press the red STOP button to clear the error.
Insert the material to be shredded. The material will be fed by
the cutter roller 16 without further assistance.
English | 19
F 016 L81 437 | (23.11.15)