Commissioning; Operation Mode - LK Armatur SmartBio LK 160 Manuel D'instruction

GB ENGLISH

Commissioning

For commissioning, the controller must be mounted correctly. All
inputs and outputs must be connected and ready for operation.
The strain relief device must be used and the terminal cover closed!
Commissioning is communicated in plain text. The user must make
a selection, confi rm and – if applicable – jump to the next menu item.
√ indicates function activated.
Now the power supply of the controller must be switched on.
After a short booting sequence
play.
0.1 Language Select language. Press OK. Scroll to Next. Press OK.
0.2 Time/Date Press OK. The year is highlighted in colour. Select year by
turning the rotary encoder. Press OK.
The month is marked. Select month. Press
Select date. Press OK.
Scroll to Time. Set time. Press OK.
Automatic summer time
OK.
Load from SD card
stalled. Press
fi le name is MMDDttmm. LKS (month, day, hour, min-
ute). Press desired fi le to load saved settings. The settings
are saved in menu 1.2. An SD card 2 GB is recommended.
Scroll to Next.
System 1.1 The controller shows the hydraulic system 1.1.
Select hydraulic system 1.1, 1.2, 2.1, 2.2, 3.1, 3.2 or 4 by
turning the encoder. Press OK.
0.7 Checklist Test outputs.
0.7.1 Test outputs The outputs can be activated manually to test the
function of the connected unit. Activate by pressing
OK and turning to ON. Press Next.
0.7 Checklist Select Mirror system.
mirrored. Press OK.
Set the desired
Select Additional
Select energy type of the additional heat source,
Oil, Gas, Pellet
and/or return pump are to be blocked when additional
heat is active. Set
1.1, 1.2, 2.1 and 2.2). Set
(System 1.1 and 1.2).
Select Tank bot. Sensor.
stalled in tank bottom.
Select HE output. Press OK. In hydraulic systems 1.1 and
1.2 it is possible to connect two pumps controlled by a
PWM-signal when RO1 and RO2 are not activated at the
same time. If a high-effi ciency pump
RO1, RO2
Select HE type. Press OK. Select signal PWM or Analog.
Press Next.
0.9 End You have completed commissioning!.
System Operation mode. From this point on the SmartBio con-
trols the thermal plant automatically. The screen displays
the hydraulic system, the date, the time, the activated
pump and the current temperature for each sensor.
Note! Check the display regularly to be able to elimi-
nate any malfunctions!
will appear on the dis-
0.1 Language
OK.
is predefined. To deactivate press
is shown only when SD card is in-
Load from SD card to read the saved fi le. The
Press OK.
Press OK.
When needed the system can be
Loading temp. (BT). (System 1.1 and 1.2)
heat. Press OK.
or - - -. Press OK. Choose if charge pump
Block chargepump to Yes or
Block returnpump
Mark checkbox if sensor is in-
is installed, select
or RO1/RO2. Press OK.
Press

Operation Mode

On the controller the user can make various settings and obtain in-
formation about states and processes. To this effect press
tomatic mode.
Select
Measured values
1.1.1 Measured
val...
1.1.2 Service hours The operating time of the activated plant components
1.1.5 Error list
1.10 Error list
1.2 Settings
1.2.1 Date setting
1.2.2 Language
1.2.7 Display
1.2.10 Buzzer
1.2 Settings
Electric,
No (System
to Yes or No
1.1.5 Error list
OK.
1.7 Login
1.9 About
appears. Select
1 Main menu
. Press .
OK
The sensor temperatures, pump speeds and status
of the connected additional heat source are shown.
Press ESC. Select Service
is displayed in hours. By actuating Reset all counters
are reset to zero. The values are saved once per day,
so that one day max. is lost in case of failure in power
supply. Press ESC. Select Error
A list of any faults that may have occured appears. Se-
lect a fault. Press OK.
The error message appears in plain text. If
necessary take the appropriate measures. Back to
1 Main menu by pressing
Settings. Press OK.
After a power failure Date/Time
of 8 hours. Select Date/Time
Press OK.
Press OK. The year is highlighted in colour.
Select year by turning the rotary encoder. Press OK.
The month is marked. Select month. Press OK.
Select date. Press OK.
Scroll to Time. Set time. Press OK.
Select Auto. Clock Change
time. Press OK. Press ESC. Select Language. Press OK.
To change over to another language select
Language. Change the language. Press OK. Press
ESC. Select Display. Press
Brightness serves to adjust the backlighting of the
display in steps of 5% from 10% to 100%.
time is used to determine the time after which, in case
of inactivity, backlighting is reduced from the set value
to 10%. Adjustable in the range from 30 to 255 sec-
onds. Mirror system. When needed the system can be
mirrored. Press ESC. Select Buzzer. Press ESC.
When activated, a warning signal sounds when an
error has occurred and/or before an additional heat
source (recharge warning) is activated. The recharge
warning buzzer sound can be switched off by press-
ing the ESC button. The recharge warning buzzer only
works if Activation is selected. Press OK.
If an SD-card has been installed, select
card safely to remove it. Press OK.
To save the settings from the SD-card, press
parameters. Successfully saved
fi le can also be read in menu 0.2 Commissioning.
Here set values can be replaced by the factory
settings. Activate factory settings? appears.Yes
or No. Press ESC twice.
System 1.1, 1.2 and 4:
Select Monitoring. Press OK. Press
System 2.1, 2.2, 3.1 and 3.2:
Select Basic functions. Press OK. The thermostat
function can be activated or deactivated. Press
three times.
Select Monitoring. Press OK. Press
If an error is indicated, check the error by pressing
OK. The error is shown in plain text. Press
times. Select Login. Press OK.
Here the installer can enter his/her login code
to perform further settings and changes. Select
About SmartBio.Press ESC.
The software and hardware version of the control-
ler, the serial number and the date of original com-
missioning appear.
If no entry is made within the preset time or by
pressing ESC twice, the display will return to the
current hydraulic system.
in au-
OK
. Press .
Evaluation OK
hours. Press OK.
list. Press OK.
ESC three times. Select
has a memory
to set date and time.
for automatic summer
OK.
Blanking
Remove SD
Remove SD-card.
Save
is shown. The saved
Error list.
ESC
Error list.
ESC three
7