Jigsaw Safety Warnings; Know Your Product - SPARKY Professional TH 65 Notice Originale

5. SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

Jigsaw safety warnings

During operation provide eye protection to
prevent eyes from exposure to flying parti-
cles. Wear goggles.
Wear hearing protection during continuous
operation. Intense noise loading during opera-
tion may damage the operator's hearing.
Take protective measures against inhala-
tion of dust. Some materials can contain
toxic ingredients. Wear a dust mask and work
with dust/chip extraction.
▪ Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
▪ Do not process materials containing asbestos. Asbes-
tos is considered carcinogenic.
▪ Use of protective gloves is recommended.
WARNING: Before connecting a tool to a
power source ensure that the voltage supply is the
same as the one specified on the nameplate of the
tool.
▪ A power source with a voltage greater than that speci-
fied for the tool can result in serious injury to the user,
as well as damage to the tool.
▪ If in doubt, do not plug in the tool.
▪ Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
▪ Fully unwind cable drum extensions to avoid potential
overheating.
▪ When an extension cable is required, you must en-
sure that it has the right ampere rating for your power
tool and it is in safe electrical condition.
WARNING: Always switch off and unplug the
power tool prior to any adjustment, servicing or main-
tenance or in case of mains drop-out.
▪ Use clamps or a vice to secure your work whenever
possible.
▪ While operating the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more securely with both hands.
▪ Do not operate the jigsaw without the fence set prop-
erly in its place.
▪ Keep hands away from the sawing range. Do not
reach under the workpiece. Contact with the saw
blade can lead to injuries.
▪ Apply the machine to the workpiece only when
Original instructions
switched on.
▪ When the cut is completed, switch the machine off
and then pull the saw blade out of the cut only after it
has come to a standstill.
▪ Take care that the base plate rests securely on the
material while sawing.
▪ Do not overload the machine: operate with moderate
pressure. Overloading occurs when you apply exces-
sive pressure, resulting in decrease of motor speed,
which may cause inefficient operation and possible
fault of the motor.
▪ Prior to sawing wood check the material for the pres-
ence of screws or nails and remove them.
▪ Always keep the cord away from the working area of
the power tool.
▪ Never use the machine with a damaged cable. Do
not touch the damaged cable and pull the mains plug
when the cable is damaged while operating. Dam-
aged cables increase the risk of electric shock.
▪ Keep work area clean. Blends of materials are par-
ticularly dangerous. Dust from light alloys can burn or
explode.
▪ Always wait until the machine has come to a complete
stop before placing it down.
▪ The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual
will be considered a case of misuse. The user and not
the manufacturer shall be liable for any damage or in-
jury resulting from such cases of misuse.
▪ To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operat-
ing instructions found in this Manual. All persons who
use and service the machine have to be acquainted
with this Manual and must be informed about its po-
tential hazards. Children and frail people must not use
this tool. Children should be supervised at all times if
they are in the area in which the tool is being used. It
is also imperative that you observe the accident pre-
vention regulations in force in your area. The same
applies for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
▪ Power tools must not be used outdoors in rainy weath-
er, or in moist environment (after rain) or in close vicin-
ity with easily flammable liquids and gases. The work-
ing place should be well lit.

Know your product

Before using the power tool, familiarize yourself with all the
operating features and safety requirements.
Use the tool and accessories only for the applications in-
tended. All other applications are expressly ruled out.
1. ON/OFF switch
2. Variable speed regulator (TH 65E, TH 70E)
3. Lock-on button
4. Fence
5. Base plate
6. Bevel angle scale
7. Saw blade
5
EN