M-system MSPK651IX Mode D'emploi page 17

Controls of Fig. 40
AUTOMATIC OPERATION WITH SENSOR:
Key A : switches the lights on/off.
Key B : enables/disables "Automatic" function. When this function is
selected, an "A" appears on the display C, and the speed of the motor
increases or decreases depending on the smoke, odours and gas present in
the kitchen.
Display C : - indicates the automatic operation of the sensor (the letter "A"
appears);- indicates the motor speed selected automatically by the sensor;
indicates the filter alarm whenever the central segment is illuminated or
flashing.
Key D : decreases motor speed / Reset; decreases motor speed to zero
(stopping); in any case however, after approximately 1 minute, the hood
resumes automatic operation at the speed set by the sensor. Whenever the
key is pressed during the display of filter alarms, a RESET occurs, and the
counting of the hours resumes again.
Key E : increases motor speed; in any case however, after approximately
1 minute, the hood resumes automatic operation at the speed set by the
sensor.
Modification of sensor sensitivity: sensor sensitivity can be modified by
operating as follows:
- stop the hood by pressing key B. – Simultaneously press keys D and E
(the sensor's sensitivity index will appear on the display) - Pressing keys D
or E, the sensor's sensitivity will either increase or decrease (1 : minimum
sensitivity / 9: maximum sensitivity). – whenever the power supply is
interrupted, the sensor will resume operation with a sensitivity index of 5.
Warning: in order to avoid damaging the sensor, never use silicone
products near the hood!
OPERATION AS TRADITIONAL HOOD:
Key A : switches the lights on/off.
Display C : - indicates the motor speed selected (from 1 to 4); - indicates
the operation of the Timer when the number is flashing; - indicates filter
alarms whenever the central segment is illuminated or flashing.
Key D : decreases motor speed / Stop / Reset; decreases motor speed to
zero (stopping). Whenever the key is pressing during filter alarm display, a
RESET occurs, and the counting of the hours resumes again.
Key E : enables the motor / increases motor speed /TIMER. Pressing this
key starts the motor (at the latest speed set); pressing the key again
increases motor speed, while keeping the key pressed down for a few
seconds enables the TIMER, and 5 minutes later the motor will stop (while
the number of speed setting selected will simultaneously begin flashing on
the display); the Timer will remain enabled if motor speed is changed. In
order to disable the Timer, press the key again.
Controls of Fig. 41
Key L: light switch.
Key 1 : B = Motor ON/OFF switch - Speed I
Key 2: B = Motor ON/OFF switch - Speed I
Key 3: B = Motor ON/OFF switch - Speed I
Key 4: B = Motor ON/OFF switch - Speed I
Filter alarm: after about 30 hours of operation, with the motor off, the speed
keys (keys 1, 2, 3 and 4) flash for 30 seconds to indicate the grease filters
need cleaning. After cleaning the grease filters (and/or replacing the
charcoal filters), restart the hour counter (RESET) by pressing key C during
filter alarm display.
Timer 5'; the timer can be started (switch-off delayed by 5 minutes) by
pressing one of the speed keys for 2 seconds(key 1, 2, 3 or 4) when the
motor is running; the selected speed key starts flashing.
Controls of Fig. 42
Key L: light switch.
Key 1: activates/deactivates the sensor (AUTOMATIC or MANUAL mode).
In Automatic mode the sensor is activeand the speed of the motor
increases or decreases depending on the smoke.- signals the filter alarm
(with motor off)
Key 2: Motor ON/OFF switch - Speed I
Key 3: Motor ON/OFF switch - Speed II
Key 4: Motor ON/OFF switch - Speed III
Filter alarm: after about 30 hours of operation, with the motor off, the speed
keys (keys 1, 2, 3 and 4) flash for 30 seconds to indicate the antigrease
filters need cleaning. After cleaning the anti-grease filters (and/or
replacingthe charcoal filters), restart the hour counter (RESET) by pressing
one of the speed keys for 2 seconds during filter alarm display.
SENSOR SENSITIVITY: When the sensor is on, the hood automatically
starts working when any smell, vapour, smoke or heat is detectedduring
cooking. The sensor sensitivi-ty can be changed according to need. For
example: very sensitive when using an electric hob or little sensitive when
using a gas hob. Change thesensitivity by simultaneously pressing key L
and key 1. The sensitivity selected will be set. Using the keys 2,3,4 you
can set the desired sensitivity. Store the new sensitivity by pressing key1.
Attention: To prevent damaging the sensor, do not use silicone products
near the hood!
Controls of Fig. 43
Button A: Turns the lights on/off. If held down for about 2" when the filter
alarm is active, it resets the hour counter.
Button B: Activates/deactivates the "Automatic" function.
Light S – Filter alarm: When the light comes on, it indicatesthat 30 h of use
have elapsed; it remains on for 30". When the light S flashes, it means that
about 120 h of operationhave elapsed. The filter reset is indicated only
when the motor is off, both in manual and automatic mode.
Automatic operation with sensor: when the button B is pressed, the
automatic function is activated. This is indicated by the corresponding LED
comingon. When the LED B flashes, it means that the sensor is waiting for
data.
Modifying sensor sensitivity: while in manual mode and with the motor off,
simultaneously press the buttons B and C. At this point, the set sensitivity
is indicated by the LED C, D or E coming on. To set the desired sensitivity
press one of the buttons C, Dor E (min, med, max). Press B again to store
it.Press button B once again to go to manual mode.
Operation as traditional hood: if in automatic mode, press the button B to
change to manual mode; the LED B goes off.Press one of the buttons C, D
or E to start the motor in 1st, 2nd or 3rd speed, respectively. Hold the
same buttondown for 2" to turn off the motor.
Controls of Fig. 44
P1: It turns on an off the light.
P2: It starts the engine setting it to the first speed (the icon is highlighted).
Other speed icons remain inactive.
P3: It starts the engine setting it to the second speed (the icon is
highlighted). Other speed icons remain inactive.
P4: It starts the engine setting it to the third speed (the icon is highlighted).
Other speed icons remain inactive.
P5: It starts the engine setting it to the fourth speed (the icon is blinking).
Other speed icons remain inactive. The maximum speed is set to be
maintained for maximum 5 minutes, after this time the speed will be
automatically adjusted to the third speed.
P6: It starts the timer (the icon is highlighted). By running the timer (5
minutes), the engine stops automatically after 5 minutes.
P7: FILTER ALARM. After 30 hours of operation the icon is highlighted to
indicate that the filter should be cleaned.
After 120 hours of operation the icon is highlighted to indicate that the
grease filter should be cleaned and the charcoal filters - replaced.
To RESET the alarm, press the icon while it is highlighted (or while it is
blinking).
Controls of Fig. 45-46
Button TC1 (Lights): Switches main light ON/OFFWhen the main light is on,
BL1 changes colour and becomes active.When the button is pressed for
more than a second, it switches the courtesy lights (optional) on/off.
Button TC2 (Motor-V1): Motor ON/OFF - Activates the motor at 1st speed.
Button TC3 (Motor-V2)Activates the motor at 2nd speed.
Button TC4 (Motor-V3)Activates the motor at 3rd speed.
Button TC5 (Motor-V4)Activates the motor at 4th speedMaximum speed is
timed at a maximum of 5 minutes, after which 3rd speed is set
automatically.When the motor is active, the LED of the last selected button
(TC2-TC5) active to signal which speed has been set.
Button TC6 (TIMER auto power off 5 min.)Activates the TIMER function at
the speed that has already been selectedIf the motor is NOT active, it
switches on the motor at the 1st speed and activates the TIMER
functionWhen the TIMER function is active, BL6 becomes active.
30h filter ALARM: after 30 hours of operation, an alarm switches on to
signal the need for anti-grease filter cleaning.The filter alarm, when active,
is displayed for 30 sec each time the motor is deactiva-ted:BL6 remains
ON.During this period, it is possible to reset the alarm by pressing the TC6
button for longer than a second.
120h filter ALARM: after 120 hours of operation, an alarm switches on to
signal the need for active carbon filter (optional) replacement.The filter
alarm, when active, is displayed for 30 sec each time the motor is
deactiva-ted:BL6 lighting blinking.During this period, it is possible to reset
the alarm by pressing the TC6 button for longer than a second.
Work Time Limit: if the hood is left on (lights and/or motor), after 10 hours
in the absence of commands from the user, it will automatically switch to
OFF condition with all services switched off.
Buzzer: the Buzzer emits a "beep" each time that a command is set from the
keyboard or remote control (optional).
Controls of Fig. 47-48
Button TC1 (Lights): Switches main light ON/OFFWhen the main light is on,
BL1 changes colour and becomes active.When the button is pressed for
more than a second, it switches the courtesy lights (optional) on/off.
Button TC2 (Motor-V1)Motor ON/OFF - Activates the motor at 1st speed.
Button TC3 (Motor-V2) Activates the motor at 2nd speed.
Button TC4 (Motor-V3)Activates the motor at 3rd speed.
Button TC5 (Motor-V4)Activates the motor at 4th speedMaximum speed is
timed at a maximum of 5 minutes, after which 3rd speed is set
automatically.When the motor is active, the LED of the last selected button
(TC2-TC5) active to signal which speed has been set.
Button TC6 (Auto ASC)Activates/deactivates the automatic ASC
function.In this mode, motor speed increases or decreases depending on