Electrical Connection; Gas Connection - ROSIERES RTV 640 PL Notice D'emploi Et D'installation

Installing a domestic appliance can be a complicated operation which if not carried out correctly, can seriously affect consumer safety.
It is for this reason that a professionally qualified person should undertake the task who will carry it out in accordance with the technical
regulations in force. In the event that this advice is ignored and the installation is carried out by an unqualified person, the manufacturer
declines all responsibility for any technical failure of the product whether or not it results in damage to goods or injury to individuals.
BUILDIN-IN
Both the worktop where the hob will be fitted and any adjacent
kitchen furniture must be
made from heat resistant material and fixed with heat resistant
adhesive.
If, when installing the hob, the lower hob face is adjacent to an
area normally accessible when handling or cleaning, fit a heatproof
partition 1 cm below the base of the hob with
a 10X10 cm opening at the rear right-hand corner, to avoid any
risk of scorching or damage.
A foam adhesive is supplied with the hob. Stick this seal under
the edge of the body as near as possible to the outer edge of the
hob. Press round the edges of the hob, so that the seal flattens
out and ensures an air tight seal.
The body of the hob is fitted with 4 location holes to take the fixing
brackets that secure the hob in the unit. Place the 4 fixing brackets
in such a way that the hob is placed perfectly in the support unit.
SEAL
accessible
space
OVEN
WITH FAN
COOLED

GAS CONNECTION

The hob can be built-in ; it is in class 3 (in compliance with gas
regulations EN 30.1.1) ;
adjoining furniture should not be higher than the level of the hob.
This appliance is not connected to an evacuation device for the
products of combustion. It must be installed and connected in
compliance with the norms in force in the country of installation.
Particular attention should be given to the availability of ventilation.
The turnover of air necessary for combustion is a minimum of 2
m3/h per kW of power.
Gas connection should be carried out in compliance with the
norms in force in the country of installation. A stop tap, a regulator
valve or a release valve for propane gas, should be fitted to the
gas supply pipe. Use only taps, regulator valves, connectors and
flexible hoses with the official mark of approval of the country of
installation.
Built-in appliance
Butane Rigid - Flexible pipe with mechanical connectors (1) -
Propane Rigid - Flexible pipe with mechanical connectors (1) -
Natural Rigid - Flexible pipe with mechanical connectors (1) -
(1) on condition that the hose is accessible along the whole of its
length it should be located so it cannot be reached by naked flame
or affected by combustion gases. Neither should it be near hot
parts of the hob nor anywhere where hot spillages could affect it.
INSTALLATION
OVEN
WITHOUT
FAN
COOLED
7 GB
2 POSSIBLES MEANS OF CONNECTION :
Fit the appliance with the cylindrical or the conical gas adaptor,
in accordance to the installation Country standards, and then
proceed to the connection, two possibilites:
• CONNECTION BY RIGID PIPE
Connect directly to the threaded end of the inlet pipe.
• CONNECTION BY FLEXIBLE PIPE WITH MECHANICAL
CONNECTOR
Screw the nuts of the flexible pipe directly on to the inlet pipe at
one end and the gas supply stop tap at the other.
We recommend this type of connection.
Important:
In all cases, make sure the seal is fitted.
Following the connection operations, test the leak tightness
using soapy water, testing by flame is strictly prohibited.
CYLINDRICAL
CYLINDRICAL

ELECTRICAL CONNECTION

"The installation must conform to the standard directives".
The manufacturer declines all responsibility for any damage that
may be caused by unsuitable or unreasonable use.
Warning : before proceeding with the connection:
• check the continuity of the earthing of the power supply
unit. We cannot be held responsible for any accident which
has resulting from the use of an appliance which is not
connected to earth, or whose earthing is defective.
• Always check before any electrical operation, the supply tension
shown on the electricity meter, the adjustment of the circuit-
breaker, the continuity of the connection to earth to the installation
and that the fuse is suitable.
• The electrical connection to the installation should be made via
a socket with a plug with earth, or via an omni pole cut-out
switch with an opening gap of at least 3 mm.
The hob is fitted with a power supply cable* without plug which
allow it to be connected only to a power supply of 230 V between
phases, or between phase and neutral.
• Connect to a 10/16 Amp socket.
Note : the socket must be reachable for any eventual repair. Take
care of its location at the time you install the hob.
* the eventual replacement of the supplying cord must be carried
on by the After Sales Service or by an agreed engineer, with a
cord whose characteristics must be similar to the original one.
. cord type H05V2V2-F (section 3 x 0,75 mm2).
CONICAL