IMPORTANT SAFETY
INSTRUCTIONS
READ AND UNDERSTAND ALL
WARNING
INSTRUCTIONS.
all instructions listed below, may result in electric
shock, fire and/or serious personal injury.
SAVE THESE
INSTRUCTIONS.
1. SAVE THESE INSTRUCTIONS - THIS OPERA-
TOR'S MANUAL CONTAINS IMPORTANT SAFETY
AND OPERATING INSTRUCTIONS.
2. DO NOT ALLOW PERSONS UNFAMILIAR WITH
THE APPLIANCE, THESE SAFETY INSTRUC-
TIONS, AND THE TOOL'S OPERATORS MANUAL
TO OPERATE THE TOOL. This appliance can be
dangerous in the hands of untrained users.
3. DO NOT OVERREACH. KEEP PROPER FOOTING
AND BALANCE AT ALL TIMES. This enables better
control of the appliance in unexpected situations.
4. ENSURE ADEQUATE SAFEGUARDS AT THE
WORK SITE (e.g. surveying site when measuring
on roads, construction sites, etc.)
5.
THE DEVISE PRODUCES VISIBLE
WARNING
LASER BEAMS, WHICH ARE
EMITTED FROM THE APPLIANCE. THIS DEVICE
IS A CLASS 2 LASER PRODUCT IN ACCORD-
ANCE WITH IEC 60825-1:2007.
6. LASER LIGHT - DO NOT STARE INTO BEAMS OR
VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
Do not point laser light at others. Laser light can
cause eye damage.
7. AVOID DANGEROUS ENVIRONMENTS. Do not
use in rain, snow, damp or wet locations. Do not use
in the presence of explosive atmospheres (gaseous
fumes, dust or flammable materials).
8. MAINTAIN TOOLS. IF DAMAGED, HAVE THE
TOOL REPAIRED BEFORE USE. Accidents may
be caused by poorly maintained tools.
9. USE TOOLS ONLY WITH SPECIFICALLY DESIG-
NATED ACCESSORIES. Use of any other acces-
sories may create risk of injury.
10. THIS TOOL IS DESIGNED TO BE POWERED BY
2 -AAA BATTERIES PROPERLY INSERTED INTO
THE TOOL. Do not attempt to use with any other
voltage or power supply.
11. DO NOT LEAVE BATTERIES WITHIN THE REACH
OF CHILDREN.
12. DO NOT MIX NEW AND USED BATTERIES.
13. DO NOT MIX BRANDS (OR TYPES WITHIN
BRANDS) OF BATTERIES.
14. DO NOT MIX RECHARGEABLE AND NON-
RECHARGEABLE BATTERIES.
15. INSTALL BATTERIES ACCORDING TO POLAR-
ITY (= / -) DIAGRAMS.
16. PROPERLY DISPOSE OF USED BATTERIES IM-
MEDIATELY.
17. DO NO INCINERATE OR DISMANTLE BATTERIES.
18. UNDER ABUSIVE CONDITIONS, LIQUID MAY BE
EJECTED FROM THE BATTERY, AVOID CONTACT.
IF CONTACT ACCIDENTALLY OCCURS, FLUSH
WITH WATER. IF LIQUID CONTACTS EYES, AD-
DITIONALLY SEEK MEDICAL HELP. Liquid ejected
from the battery may cause irritation or burns.
19. KEEP HANDS AWAY FROM ALL MOVING PARTS.
20. WATCH OUT FOR ERRONEOUS MEASURE-
21. CARRY OUT PERIODIC TESTS MEASURE-
Failure to follow
22. DO NOT DISPOSE OF TOOL OR BATTERIES TO-
23. HAVE YOUR TOOL SERVICED BY A QUALIFIED
24. MAINTAIN LABELS AND NAMEPLATES. These
25. THE DEVICE CONFORMS TO THE MOST STRIN-
LASER 2 Class 2 Laser Product
Cat. No. ................................................ 48-22-9802
Range ................................................ 150' (45.7 m)
Cat. No. ................................................ 48-22-9803
Range .............................................. 330' (100.6 m)
Volts................................................ 3 DC (2 x AAA)
Laser Class............................................................2
Laser Type ..................................... 635nm, < 1 mW
Storage Temperature ....................... -13°F to 158°F
Operating Temperature .................... 14°F to 122°F
Distance Measurement:
Typical tolerance* ................... ± 1.5 mm / 0.06 in **
Maximum tolerance
Smallest unit displayed ...................1 mm / 0.001 m
* Applies for 100 % target reflectivity (white painted wall), low
** An additional tolerance of 0.1 mm/m should be taken into
*** An additional tolerance of 0.15 mm/m should be taken into
2
MENTS IF THE TOOL IS DEFECTIVE OR IF IT
HAS BEEN DROPPED, MISUSED OR MODIFIED.
MENTS. Particularly after the tool has been subject
to abnormal use, and before, during and after im-
portant measurements.
GETHER WITH HOUSEHOLD WATER MATERIAL!
Appliance and batteries that have reached the end of
their life must be collected separately and returned
to an environmentally compatible recycling facility.
REPAIR PERSON USING ONLY IDENTICAL
REPLACEMENT PARTS. This will ensure that the
safety of the tool is maintained.
carry important information. If unreadable or miss-
ing, contact a MILWAUKEE service facility for a free
replacement.
GENT REQUIREMENTS OF THE RELEVANT
ELECTROMAGNETIC COMPATIBILITY (EMC)
STANDARDS AND REGULATIONS. Yet, the possi-
bility of causing interference in other devices cannot
be totally excluded.
READ AND SAVE ALL
INSTRUCTIONS FOR
FUTURE REFERENCE.
SYMBOLOGY
Volts
Direct Current
WARNING
Read Operator's Manual
Laser product - Avoid Exposure:
Laser Radiation Is Emitted From
This Aperture
European Conformity Mark
SPECIFICATIONS
...........± 4.0 mm / 0.16 in ***
****
background illumination, 25 ºC
account
account
Laser Light - Do Not
Stare Into Beam