Peg-Perego book plus ns Notice D'emploi page 14

on the frame, press the seat downwards to
ensure it engages securely onto the base.
2 FITTING THE WHEELS: Slot the uprights into the
rear wheel crosspiece (fig_a), ensuring that it is
facing the right way, then push the rear wheels
on and make sure that they click into place
(fig_b). To mount the front wheels, fit them into
the uprights until they lock into place (fig_c).
3 ATTACHING THE MAIN HANDLE: if the handle
tube faces upwards, align it with the stroller
(Fig_a).
Fasten the handle to the frame as shown in
the figure (Fig_b).
To complete the operation, press the two side
buttons on the handle (Fig_c) to ensure the
handle pushes in all the way, until it clicks
into place (Fig_d).
4 FITTING THE BASKET: if lowered, lift the
basket tube to the horizontal position. Press
the silver buttons under the metal basket
tube located at the back of the stroller (fig_a)
and remove the metal tube (fig_b). Thread
the tube through the fabric loop on the
back of the basket, making sure that the two
silver buttons are facing downward (fig_c).
Re-attach the tube to the housings (fig_d).
5 Secure the two upper basket vinyl eyelets to
the two grey buttons on either side of the metal
tube housing. Please note that the eyelets open
(fig_e). Remove the cardboard from the lower
rear bar. IMPORTANT! Secure the two lower
basket vinyl eyelets to the two grey buttons
on the top of the lower rear bar. Please note
that the eyelets open (fig_f). WARNING! If this
operation is not performed correctly, the basket
will not properly hold the weight.
Attach the basket tabs to the grey buttons on
the front of the frame (figure).
REFER TO OUR INSTALLATION INSTRUCTIONS
VIDEO AT: WWW.PEGPEREGO.COM
6 FIXED OR SWIVELING FRONT WHEELS: Lift the
levers to prevent the wheels from swiveling
(fig_a) and lower them to allow the wheels to
swivel (fig_b). On uneven surfaces, the wheels
should be set to their fixed position.
7 BRAKE: Press the lever down to apply the brake
on the chassis and lift it to release the brake.
8 ADJUSTABLE HANDLEBAR: To adjust the height
of the handlebar, press both of the side buttons
at the same time (fig_a) and swing it into the
desired position (fig_b), then release the buttons.
9 FASTENING THE SEAT TO THE CARRIAGE: Seat
Pop-Up can be secured to the carriage either
facing mom or the street. Place it centrally on the
carriage alongside the symbols (fig_a) and press
downwards with both hands until it clicks into
place (fig_b). To ensure it is properly secured, grab
the seat from the front bar and pull upwards.
1 0 RELEASING THE SEAT FROM THE CARRIAGE:
Press the two buttons on the armrests of the
seat (fig_a) and then the two levers underneath
(fig_b); pull up the seat (fig_c) until it releases.
If the backrest is fully reclined forward (in the
closed position, facing the world), the seat
cannot be released from the chassis (fig_d).
In this case, lift the backrest to the position of
use before releasing the seat from the chassis
(fig_e). If the backrest is fully reclined forward (in
the closed position, facing the world), the seat
cannot be released from the chassis (fig_d). In
this case, lift the backrest to the position of use
before releasing the seat from the chassis (fig_e).
1 1 FRONT BAR: To attach the front bar, slide the
attachments into the armrests and push towards
the seat until they lock into place (fig_a). To
remove the front bar, press the two buttons (fig_b)
and pull out (fig_c). Open the front bar on one side
only, to facilitate the child's entry and exit.
1 2 HOOD: To fasten, slide the attachments into
the sides of the seat (fig_a) and button the
hood to the back of the backrest (fig_b). To
remove the hood: pull out the attachments
and unbutton. To lift the hood: pull it towards
you; to close the hood: push it back. The hood
includes a slot from which you can hang the
child's favorite toy (fig_c).
1 3 When the backrest is fully reclined, open the
hood using the double slider on the back (fig_a).
To provide your child greater ventilation, lift the
hood section fastened with Velcro (fig_b).
1 4 BACKREST: to adjust the backrest, lift the
handle (fig_a) and recline it to the desired
position (fig_b).The backrest can be adjusted
into different positions.
1 5 FOOTREST: before adjusting the foot rest,
ensure its cover is accurately fitted; if it isn't,
fit it accordingly. To lower the footrest push
the two levers downwards and then push
the footrest downwards (fig_a); to raise the
footrest lift it upwards (fig_b).
1 6 FIVE POINT SAFETY HARNESS: To fasten it,
push the two waist strap buckles (with the
shoulder straps attached – arrow_a) into
the leg divider until they click into place
(arrow_b). To unfasten it, press the round
button in the centre of the buckle (arrow_c)
and pull the waist straps out (arrow_d).
1 7 To tighten the waist strap, pull on both sides
in the direction of the arrow (arrow_a). To
loosen it, move it in the opposite direction.
1 8 To adjust the height of the safety harnesses,
release the two buckles on the rear of the backrest.
Pull the shoulder straps towards you (arrow_a)
until the buckles are released and insert them
in the backrest loops (arrow_b). Remove the
shoulder straps from the sack (arrow_c) and
insert them in the most appropriate loop
(arrow_d), then re-attach the two buckles on the
rear of the backrest (arrow_e) The buckles are
securely attached when a click is heard (fig_f).
1 9 RAIN CANOPY: position the rain canopy on
the stroller (fig_a) and insert the two lateral
- 14 -