Before Operation; Working With Your Machine - Stihl GHE 355 Manuel D'utilisation

Masquer les pouces Voir aussi pour GHE 355:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 57
Secure the machine on the load floor using
adequately dimensioned fastening
material (straps, ropes etc.) at the
fastening points described in this
instruction manual. (
12.3)
Push or pull the machine at walking pace
only. Do not tow!
When transporting the machine, always
observe regional legislation, especially
regarding load security and the transport
of objects on load floors.

4.5 Before operation

Make sure that only persons who are
familiar with the instruction manual are
permitted to use the machine.
Observe the local regulations regarding
permitted operating times for gardening
power tools with combustion engines or
electric motors.
All faulty, worn or damaged parts must be
replaced before using the machine.
Replace any illegible or damaged danger
signs and warnings on the machine. Your
STIHL specialist has a supply of
replacement stickers and all the other
spare parts.
Before initial operation, it must be ensured
– that the machine is in good operational
condition. This means that the covers
and guards must be in place and in
good condition.
– that it is connected electrically to a
properly installed socket.
– that the insulation of the electric cable,
extension cable, plug and connector is
in good condition.
0478 201 9914 B - EN
– that the complete machine (motor
housing, guards, fastening elements,
blades, blade shaft, blade discs etc.) is
neither worn nor damaged.
– that there is no shredding material in
the machine and that the feed chute is
empty.
– that all screws, bolts, nuts and other
fastening elements are in place and
properly tightened. Tighten any loose
screws, bolts and nuts prior to initial
operation (observe tightening torques).
Only use the machine out-of-doors and not
close to walls or any other solid objects in
order to prevent the risk of injuries and
property damage (no escape for the user,
broken windows, scratched cars etc.).
The machine must placed in a stable
position on firm and level ground.
Do not use the machine on a paved or
gravel-covered surfaces, as ejected or
thrown-up material could cause injuries.
Before using the machine, always check
that it is properly closed. (
Make sure that you are familiar with the
On / Off switch so that you can react
quickly and correctly in any emergency
situation.
The splash guard in the feed chute must
cover the feed opening and must be
undamaged – replace the splash guard if
damaged.
Risk of injury:
Only operate the machine when properly
assembled. If parts of the machine
(e.g. wheels) are missing, the specified
safety distances are no longer maintained
and the stability of the machine may also
be reduced.
Before using the machine, always carry
out a visual check to ensure that it is in
good operating condition.
"Good operating condition" means that the
machine is fully assembled, in particular:
– Upper chute is installed on lower chute
– Feed chute is installed on basic unit and
both closure screws are fastened hand-
tight
– Wheel carrier assembly is installed
– Both wheels are mounted
– All safety devices (ejection chute,
splash guard etc.) must be present and
functional
– Cutting unit (blade disc) is installed
– All blades are properly installed
The switch and safety devices installed in
the machine must not be removed or
bypassed.
Visually inspect the blade disc for damage
and deformation; replace if necessary.
11.3)

4.6 Working with your machine

Do not operate the machine in the rain or
during thunder storms, particularly when
there is a risk of lightning strike.
The risk of accidents is higher if the ground
is damp due to increased danger of
slipping.
Particular caution should be exercised
during working in order to prevent slipping.
If possible, avoid using the machine when
the ground is damp.
Never work when animals or
persons, particularly children,
are in the danger area.
39

Hide quick links:

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Ghe 375

Table des Matières