Whirlpool W10505965B Instructions D'installation page 5

3. Apply masking tape to the end of a 7 mm (⁹⁄₃₂") nut driver to
help hold the gas orifice spud in the nut driver while changing
it. Press nut driver down onto the gas orifice spud and
remove by turning it counterclockwise and lifting out. Set gas
orifice spud aside.
A
B
A. Orifice spud
B. Orifice spud holder
4. Locate the nameplate on the range. It will be located on the
front frame behind the oven door or drawer front depending
on model. Identify the burner ratings for this range from the
nameplate.
Refer to the following chart for the gas to be used after the
conversion. Identify the correct replacement orifice spuds
using the nameplate burner ratings. The colors and ID
number are marked on the hex flats of the orifice spuds.
Natural Gas Orifice Spud Chart for Surface Burners
Nameplate Burner
Ratings (sea level)
Natural Gas LP
18,000 BTU 14,200 BTU
17,000 BTU 14,200 BTU
15,000/ 14,200 BTU
15,500 BTU
13,000/ 11,000 BTU
13,500 BTU
12,000/ 11,000 BTU
12,500 BTU
9,500 BTU 8,000 BTU
8,000 BTU 8,000 BTU
5,000 BTU 5,000 BTU
*Same orifices as shipped from factory for Natural gas.
C
D
C. Screw
D. Spark electrode
A
A. Hex flat
Replacement Orifice - Natural
gas (high altitude)
Color Size ID
Number
Red/ 1.90 mm N190
Orange
Red/ 1.90 mm N190
Orange
Red/ 1.90 mm N190
Orange
Yellow/ 1.70 mm N170
Magenta
Yellow/ 1.70 mm N170
Magenta
Red/ 1.40 mm N140
White
Red/ 1.40 mm N140
White*
Red/ 1.10 mm N110
Brass*
LP Gas Orifice Spud Chart for Surface Burners
Nameplate Burner Ratings
(sea level)
Natural Gas LP
18,000 BTU 14,200 BTU
17,000 BTU 14,200 BTU
15,000/ 14,200 BTU
15,500 BTU
13,000/ 11,000 BTU
13,500 BTU
12,000/ 11,000 BTU
12,500 BTU
9,500 BTU 8,000 BTU
8,000 BTU 8,000 BTU
5,000 BTU 5,000 BTU
NOTE: Refer to the Model Number and Serial Number Plate
located on the oven frame behind the top left side of the oven
door for proper sizing of spuds for each burner location.
5. Save the replaced orifice spuds in a plastic bag or other
container.
6. Replace the burner base using both screws.
7. Replace burner cap.
8. Repeat steps 1-7 for the remaining burners.
To Convert Oven Bake Burner
1. Remove the oven racks.
2. Remove 2 screws at the rear of the oven bottom.
3. Lift the rear of the oven bottom up and back until the front of
the panel is away from the front frame. Remove from oven
and set it aside on a covered surface.
A
A. Screws
B. Oven bottom
Replacement Orifice - LP gas
(high altitude)
Color Size ID
Number
Yellow/ 0.99 mm L99
Brown
Yellow/ 0.99 mm L99
Brown
Yellow/ 0.99 mm L99
Brown
Yellow/ 0.88 mm L88
Black
Yellow/ 0.88 mm L88
Black
Yellow/ 0.84 mm L84
Green
Yellow/ 0.84 mm L84
Green
Yellow/ 0.65 mm L65
Silver
B
5