Bosch GTM 12 JL Professional Notice Originale page 41

OBJ_BUCH-1688-007.book Page 41 Friday, February 24, 2017 12:15 PM
Material stop
75 Clamping screw of the material stop
76 Drill holes for material stop
77 Material stop*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Combination Saw
Article number 3 601 M15 ...
Rated power input
No-load speed min
Laser type nm
mW
Laser class
Divergence of laser line
Weight according to
EPTA-Procedure
01:2014 kg
Protection class
Permissible workpiece dimensions (maximal/minimal):
Chop/mitre saw, see page 45
Table saw, see page 48
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter
Noise Information
Sound emission values determined according to
EN 61029-2-11.
Typically the A-weighted noise levels of the product are:
Sound pressure level 91 dB(A); Sound power level
104 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
The noise emission value given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It may also
be used for a preliminary estimation of noise emissions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used for
other applications, with different accessories or is poorly
maintained, the noise emission value may differ. This may sig-
nificantly increase noise emissions over the total working pe-
riod.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually being
used, should also be taken into account. This may significant-
ly reduce noise emissions over the total working period.
Bosch Power Tools
Assembly and Transport
 Avoid unintentional starting of the machine. During as-
Delivery Scope
Carefully remove all parts provided from their packaging.
Remove all packing material from the power tool and the ac-
cessories provided.
GTM 12 JL Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
... 0.. ... 061
– Combination saw with pre-mounted saw blade
W 1800 1650
– Allen key/slotted screwdriver 5
-1
3800 3700
– Dust bag 8
650 650
Additionally for table saw:
< 1 < 1
– Parallel guide 61
2 2 – Push stick 62
– Lower saw blade cover 66
1.5 mrad 1.5 mrad
Note: Check the power tool for possible damage.
(full angle) (full angle)
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
21.1 21.1
All parts must be properly mounted and all conditions fulfilled
/II /II
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Stationary or Flexible Mounting
 To ensure safe handling, the machine must be mounted
mm 300–305
Mounting to a Working Surface (see figures a–b)
mm 1.5–2.0
– Fasten the power tool with suitable screw fasteners to the
mm 30
or
– Clamp the power tool with commercially available screw
Mounting to a Bosch Saw Stand
With the height-adjustable legs, Bosch GTA saw stands pro-
vide firm support for the power tool on any surface. The work-
piece supports of the saw stand are used for underlaying long
workpieces.
 Read all safety warnings and instructions included with
 Assemble the worktable properly before mounting the
– Mount the power tool in transport position on the saw stand.
Flexible Mounting (not recommended!)
In exceptional cases, when it is not possible to mount the ma-
chine onto a level and stable work surface, it can be set up us-
ing the tilt protector.
The tilt-protector bar 6 is used for this purpose.
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
on a level and stable surface (e. g., workbench) prior to
using.
working surface. The mounting holes 3 serve for this pur-
pose.
clamps by the feet to the working surface.
the worktable. Failure to observe safety warnings and in-
structions can lead to electrical shock, fire and/or cause
serious injuries.
power tool. Perfect assembly is important in order to pre-
vent the risk of collapsing.
English | 41
1 609 92A 3S7 | (24.2.17)