Product Description And Specifications; Intended Use; Product Features - Bosch GTM 12 JL Professional Notice Originale

OBJ_BUCH-1688-007.book Page 40 Friday, February 24, 2017 12:15 PM
40 | English
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.

Intended Use

The power tool is intended as a stationary machine for making
straight lengthways and crossways cuts in wood. Horizontal
mitre angles of –48° to +48° as well as vertical bevel angles
of –2° to +47° are possible.
The machine is designed with sufficient capacity for sawing
hard and softwood as well as press and particle board.
When operating as a table saw, the power tool is not permit-
ted for cutting aluminium or other non-ferrous metals or al-
loys.
The light of this power tool is intended to illuminate the power
tool's direct area of working operation and is not suitable for
household room illumination.

Product Features

The numbering of the components shown refers to the repre-
sentation of the power tool on the graphic pages.
1 OFF button
2 ON button
3 Mounting holes
4 Recessed handles
5 Allen key (size 6 mm)/slotted screwdriver
6 Tilt-protector bar
7 Saw blade
8 Dust bag
9 Chip ejector
10 Locking screw of lever 11
11 Bracket
12 Hex socket screw for mounting of saw blade
13 Spindle lock
14 Clamping flange
15 Interior clamping flange
16 Laser lens cover
Chop and Mitre Saw Features
17 Release button of the tool arm
18 Handle
19 Laser unit/Laser radiation outlet
20 Retracting blade guard
21 Material clamp
22 Saw table of the chop and mitre saw
23 Scale for mitre angle
24 Insert plate
25 Locking knob for various mitre angles
26 Mitre detent lever
27 Detents for standard mitre angles
1 609 92A 3S7 | (24.2.17)
28 Mounting holes for material clamp
29 Saw-table extension
30 Fence
31 Adjustable fence
32 Stop screw for 33.9° bevel angle (vertical)
33 Stop bolt for 33.9° bevel angle (vertical)
34 Lighting unit
35 Light switch ("Light")
36 Switch for marking of cutting line ("Laser")
37 Bevel lock lever
38 Transport safety-lock
39 Hex socket screws (6 mm) of the fence
40 Laser warning label
41 Hex socket screws of the saw table extension
42 Threaded rod
43 Wing bolt
44 Locking screw of the adjustable fence
45 Locking bracket
46 Fine scale
47 Indicator for bevel angle
48 Scale for bevel angle
49 Screws for insert plate
50 Rubber cap (front)
51 Adjustment screw for laser position
(parallelism)
52 Adjustment screw for laser position (flush levelling)
53 Rubber cap (side)
54 Adjustment screw for laser position
(lateral deviation)
55 Screw for fine scale
56 Screw for bevel angle indicator
57 Allen screw (size 3 mm) for standard bevel angle 0° (ver-
tical)
58 Allen screw (size 3 mm) for standard bevel angle 45°
(vertical)
Table Saw Features
59 Saw table of the table saw
60 Riving knife
61 Parallel guide
62 Push stick
63 Blade guard
64 Clamping handle of the parallel guide
65 Scale for clearance of the saw blade to the parallel guide
66 Lower saw blade cover
67 Pins for attachment of the hold-down stick
68 Clamping lever
69 Clearance indicator
70 Screw for parallel guide clearance indicator
71 Guide of the parallel guide
72 Adjustment screw for tightening tension of guide 71
73 Screws inside the glide pad of the parallel guide
74 Set screws of the parallel guide
Bosch Power Tools