Exo Terra PT 2060 Mode D'emploi page 3

of the appliance. The longer extension cord should be arranged
so that it will not drape over the counter top or table where it
could be pulled on by children or tripped over unintentionally.
SAvE THESE INSTRUCTIONS.
Introduction
The Exo Terra Wire Light has a heat resistant porcelain socket
®
designed to withstand up to 250 Watts. Ideal for use with Heat Wave
Lamps (ceramic heat emitters), self-ballasted mercury vapour bulbs,
and all types of regular incandescent bulbs. The wire guard prevents
unnecessary heat build-up. Combine the Wire Light with the Exo
Terra Light Bracket (PT2223) to suspend it securely above any
®
glass terrarium.
Installation
A
4
Installation hanging from the ceiling or an elevated platform:
1. Screw light bulb into the Exo Terra
wattage guidelines). TIP: apply a thin layer of petroleum jelly to
the threads on the base of the light bulb before screwing it in.
This will make it easier to unscrew the bulb when it is time to
replace it.
2. Insert Hanger into the mounting brackets located on either side of
the lamp socket (A).
3. Suspend Exo Terra Wire Light from ceiling or other elevated
®
platform using a chain or other recommended suspension
method. Ensure that the lamp is positioned over the top metal
screen portion of your terrarium and NOT over any glass, plastic
parts, or other flammable material. Failure to do so could result in
a possible fire hazard.
4. Keep unit out of reach of children. Keep unit away from curtains or
other flammable objects.
Installation with Light Bracket (Sold separately PT2223):
1. Screw light bulb into the Exo Terra
wattage guidelines). TIP: apply a thin layer of petroleum jelly to
the threads on the base of the light bulb before screwing it in.
This will make it easier to unscrew the bulb when it is time to
replace it.
2. Insert Hanger into the mounting brackets located on either side
of the lamp socket (A).
3. Clean the outside surface of the terrarium glass.
4. With the protective backing still intact, place the Light Bracket
support on the back or the side of the terrarium to determine its
Wire Light (follow maximum
®
Wire Light (follow maximum
®
final position.
5. Mark the position with a wax pencil or other marker.
6. Remove the protective backing and carefully fit the Light Bracket
support within the marked area.
7. Make sure the tape is pressed evenly against the terrarium glass
and that no air bubbles are showing.
8. Press the adhesive sides firmly against the glass panel for at
least 30 seconds.
9. Wait a few moments and make sure the tape is attached firmly to
the terrarium before suspending the fixture.
10. Once in place, the Light Bracket should not be removed.
11. Adjust the height and tighten the screw of the Light Bracket
when the Exo Terra Wire Light is suspended above the terrarium
®
at the desired height.
12. Remove the first rubber washer and slide the ring of the fixture's
support tightly in between both rubber stoppers.
13. Adjust the position of the Exo Terra
remaining rubber washer.
14. Replace the first rubber stopper to secure the ring of the fixture's
support tightly in between both rubber stoppers.
15. Ensure that the light's focal point is not positioned above any
plastic parts of the terrarium or screen cover to prevent damage.
16. Keep unit out of reach of children. Keep unit away from curtains
or other flammable objects.
Main Parts
1. 6 ft (1.80 m) power cord
2. Ceramic socket
3. Wire guard
4. Hanger
3
Application
Wire Light PT2060 for use with:
Heat Emitter 40 W (PT2044)
Heat Emitter 60 W (PT2045)
Heat Emitter 100 W (PT2046)
Heat Emitter 150 W (PT2047)
Solar Glo 125W (PT2192)
Wire Light PT2062 for use with:
Heat Emitter 250 W (PT2048)
Solar Glo 160W (PT2062)
® Wire Light by moving the
4
2
1