Safety Instructions - Kyocera TJEP Manuel D'utilisation

User guide
Before using this tool, it is important that all users read the manual and the
technical specifications carefully. These documents should be kept with the
tool. For questions, please contact the vendor of the tool.

Safety instructions

Read and learn all safety and operating instructions
thoroughly before using the TJEP stapler. Follow all
safety regulations carefully. By failing to follow the
safety regulations, you may harm yourself or others.
Keep the stapler away from children. The stapler is
dangerous in the hands of an untrained person.
The tool may only be used for nailing wood or materials
with similar hardness.
Always use safety glasses and hearing
protection when the stapler is in use. Other
people in the work area should use
appropriate personal protective equipment
such as eye and ear protection.
Always remove the air supply from the stapler, when the
stapler is not in use, before maintenance, cleaning or if
a staple has jammed.
Cleaning and maintenance
Test regularly that all nuts, bolts and parts are tighten.
Clean and maintain the stapler regularly, and keep it
free of grease and dirt. Lubricate the driverpiston lightly,
and use only acid free oil dedicated to pneumatic nail-
ers.
Never use a damaged stapler. The stapler may only be
repaired by qualified persons.
TJEP stapler
Do not use the stapler to perform other jobs than the
designated function. Never play with the stapler, and
never point the stapler towards yourself or other per-
sons, even if it is not loaded.
Hold the stapler so that your head and body
are not in danger in case of a backlash
caused by faults in energy supply or hard
surfaces.
Use only staples and parts specified by the manufac-
turer, otherwise there is a risk of accident and resulting
injury.
Do not modify or repair the stapler in any way. Never
tamper with the safety bracket on the stapler. The
stapler may function unexpectedly after and cause
dangerous situations.
8
Be aware of workplace conditions. The stapler can
shoot through thin workpieces, or the staples may slip
off if shooting close to the edge, and this may injure
another person. Only use the stapler on the workpiece.
When using the stapler, never hold it near the nozzle,
and do not shoot upon other stables or metals.
Do not load staples into the tool if the trigger or nozzle
is activated. Always connect the air supply before load-
ing staples.
Never damage the tool house. The tool house is a pres-
sure chamber.
The stapler should only be transported when discon-
nected from the air supply. The stapler should not be
carried in the air hose, and keep your finger away from
the trigger.
Always connect the male free flow nipple to the stapler
side of the air hose, so that the stapler is depressurized
when disconnected from the hose.
Do not exceed the specified maximum air pressure of
the stapler (1 bar = 15 psi). Do not use any kind of gas,
oxygen or other energy sources for the stapler as this
may cause an explosion.
Optimal use of the stapler
To avoid unnecessary noise development and wear
on the stapler, it should only be used with the correct
air pressure for the purpose. The stapler should only
be connected to air hoses approved to withstand the
maximum air pressure of the tool + 10%.
For each stapler there should be a water separator,
air greaser and a reducing valve. If an air greaser is
not connected, it is recommended to grease the tool's
intake with a few drops of acid-free oil - approx. 4-5
drops per 500 shots.
Optimum air supply is achieved using an air hose with
a diameter of 3/8" or 10 mm. If the air hose is too long,
this may cause lack of pressure and air supply.
The air consumption is stated in the tool's technical
specifications.
Compressor and air hose/air supply are factors which
have a great influence on the function and speed of
your tool.
If you have any questions, please contact your TJEP
dealer or KYOCERA UNIMERCO Fastening A/S.