Intended Use; Assembly And Adjustments - DeWalt D25810 Guide D'utilisation

English
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. D
if this tool does not operate, check power supply.
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

INTENDED USE

Your heavy-duty chipping hammers is designed for
professional concrete chiseling applications.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
Your heavy-duty chipping hammer is a professional power
tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
4
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
WALT tools are factory tested;
e
Side Handle (Fig. A–B)

WARNING: To reduce the risk of personal injury,
ALWAYS operate the tool with the side handle
properly installed. Failure to do so may result in
the side handle slipping during tool operation and
subsequent loss of control. Hold tool with both hands
to maximize control.
The side handle clamps to the front of the gear case and
3
may be rotated 360˚ to permit right- or left-hand use.
Mounting the Straight Side Handle
(Fig. B)
1. Widen the ring opening of the side handle
rotating it counter clockwise.
2. Place the assembly onto the putting the nose of the tool
through the steel ring 9
the bit holder and sleeve.
3. Rotate the side handle assembly to the desired position.
For hammerdrilling horizontally with a heavy drill
bit, place the side handle assembly at an angle of
approximately 20° to the tool for optimum control.
4. Lock the side handle mounting assembly in place by
securely tightening the handle
so that the assembly will not rotate.
Fig. B
9
2
Bit and Bit Holder

WARNING: Burn Hazard. ALWAYS wear gloves when
changing bits. Accessible metal parts on the tool and
bits may get extremely hot during operation. Small
bits of broken material may damage bare hands.

WARNING: Do not attempt to tighten or loosen drill
bits (or any other accessory) by gripping the front part
of the chuck and turning the tool on. Damage to the
chuck and personal injury may occur.
The rotary hammer can be fitted with various chisel bits
depending on the desired application. Use sharp bits only.
Inserting and Removing SDS Max Bits
(Fig. C)
nOTE: Accessories and attachments used must be
lubricated around the SDS MAX fitment before installation.
1. Pull back the locking sleeve 8 and insert the bit shank.
The bit shank must be clean.
by
2
and onto the collar 10 past
2 rotating it clockwise
10