Operation; General - Hatco Rapide Cuisine IRNG Série Manuel D'installation Et D'utilisation

English

General

Use the following information and procedures to operate
H Type Induction Ranges. NOTICE: Do not move a
countertop unit during operation.
WARNING
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
CAUTION
BURN HAZARD:
• Do not leave metal objects or utensils on or near
induction range. They may become hot.
• Use caution when wearing rings, watches, or other
ferrous objects around induction range. They may
become hot.
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
Pan Specifications
Pans used with an Induction Range must meet the following
specifications:
• Made of material with magnetic properties (ferrous
material)
- Enameled Steel Pans
- Cast Iron Pans
- Stainless Steel Pans
- Aluminum Pans w/ferrous base
• Proper size ( measurements given are the pan bottom
diameter)
- Minimum = 4" (102 mm), Maximum = 13" (330 mm)
• Flat bottom
The following pans cannot be used with an Induction Range:
• Glass Pans
• Aluminum Pans without a ferrous base
• Earthenware Pans
• Ceramic Pans
• Copper Pans
NOTE: The Induc ti on
automatically detects if a pan
is induction-ready. If a pan
is placed on the unit during
operation that is not induction-
ready, a pan icon with the
message "Non-Compatible"
will appear on the Control Display, and the unit will not
operate.
Timer
Button
Form No. IRNGHM-0117
Range
H Type Induction Range Control Panel
Startup
1. Before turning on the unit each day, clean the glass cooking
surface using an appropriate cleaning wipe, damp paper
towel, or a damp cloth. CAUTION! Wipe up all spills and
splashes immediately. Make sure unit is dry before
using. Do not allow liquid to run into air inlet filter on
bottom of unit.
NOTE: The unit can be turned off at any time by pushing the
Control Knob.
NOTE: The cooling fan in the unit will not start until the unit gets
hot. Once the fan turns on, it will run until the unit cools.
2. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.
• A Welcome Screen will appear on the Control Display for
a few seconds, then the display will go blank.
3. Place an induction-ready pan on the unit. The Induction
Range will not operate without a pan centered inside the
cooking zone pattern on the glass cooking surface.
4. Push the Control Knob to start the
Induction Range.
• The Power Control Screen
appears showing a bar graph
and a percentage of power
setting.
NOTE: The pan icon on the display
will flash without heat waves when a pan is not being
heated or when no pan is on the glass cooking surface.
The icon will remain solid with heat waves when a
compatible pan is on the cooking surface and being
heated.
5. Turn the Control Knob to adjust the Power setting to the
desired percentage.
• Turn the Control Knob clockwise to increase the setting.
Turn the Control Knob counterclockwise to decrease the
setting.
• Most cooking in Power Control will be done at a setting
of 50% or less. Start with a lower setting because the
unit gets hot quickly. Make adjustments as necessary.
NOTE: Heat generation will stop automatically whenever a pan
is removed from the glass cooking surface. The unit will
hold the current setting for three minutes. If the pan is
placed back on the unit within the three minutes, the
unit will resume cooking at the current setting. After
three minutes, the Control Display will go blank and the
unit will shut off.
Shutdown
1. Push the Control Knob to turn off the Induction Range, the
Control Display will go blank.
NOTE: Heat generation will stop automatically whenever a pan
is removed from the glass cooking surface.
Control Display
(showing Welcome Screen)
7

OPERATION

Control
Knob