Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 8
Operation
After unpacking the product, pull out the shredder bin or
1
bag frame (depending on model) and remove the CD shard
tray, which sits on top of the bag frame on departmental
models or bin on small office models. Store this tray on the
external location points (i) and use when you shred CD's or
credit cards to separate waste for recycling (not applicable
for RSM1130, RDM1150, RDM1170, RDSM750 and
RDSM770 models).
Connect shredder to mains supply.
2
Ensure the on/off button on the back of the machine is in
3
the on position (d).
To commence shredding, press the central Auto button (e).
4
This will illuminate the anti jam indicator.
This sets the shredder into auto mode and initiates the
Mercury anti jam mechanism. The standby symbol will
illuminate blue and the anti-jam indicator will glow green.
You are now able to shred.
Insert paper to be shredded into the feed area. The Mercury
5
anti jam mechanism will sense the thickness of the paper
being shredded.
If the paper thickness is within the shredder's capacity,
the motor will start and your documents will be shredded.
Cutters will stop once the shredding process is complete.
If the paper thickness is greater than the shredder's sheet
capacity, the anti-jam indicator will turn from green to red
and the motor will not run.
If this happens, remove some of the sheets from the paper
6
stack and re-try until the anti-jam indicator reverts back to
green, the shredder will then automatically start and allow
the paper to be shredded.
If the shredder is left in auto mode for more than 2 minutes
7
without being used, the shredder will automatically turn
back to standby mode in order to save power.
The shredder will automatically 'wake up' from sleep mode
8
when paper is inserted into the shredder mouth. There is no
need to press the Auto button (e).
6

Reverse Function

Should you wish to reverse the shredding direction whilst
1
shredding a document, a reverse button (f) has been fitted
for your convenience.
By pressing the reverse button the shredding cutters will
2
change direction allowing the retrieval of the document
being shredded. The anti-jam indicator will turn to red.
The reverse function will only run whilst the button is being
3
pressed. When the reverse button has been released the
shredder will revert to stand by mode.
To turn back to auto mode, press the auto button (e).
4
CD and Credit Card Shredding
Models RSM1130, RDM1150, RDM1170, RDSM750 and
RDSM770 can not shred CD's or credit cards, therefore this
section is not applicable to these three models. All other
Mercury models can shred CD's and credit cards as follows:
A separate CD tray is provided to collect the shredded CD
1
shards. Ensure that this is correctly mounted onto the bin
rail or internal bin (small office models) before shredding
CDs or credit cards. CD and credit card shards should be
disposed of separately to paper.
Pull up the CD guide (h) located in the centre of the feed
2
area and flip it into position over the shredder mouth.
For credit card shredding, switch the shredder to auto mode
3
and insert the card in line with the arrow marked on the
shredder mouth. Only shred 1 credit card at a time.
For CD shredding, extend the sides of the CD guide, switch
4
the shredder to auto mode and place the CD into the centre
of the CD slot. Only shred 1 CD at a time.
Empty the CD tray after 8 credit cards or CD's to avoid
5
waste spilling over into the paper waste bin. Remove the CD
tray before recommencing to shred paper.

Publicité

Table des Matières
loading

Table des Matières