Fitting The Elements Onto The Appliance; Plugging In The Power Cord And Switching On The Appliance; Storing And Transporting The Appliance - Rowenta SILENCE FORCE RO83 Série Mode D'emploi

USE
1 • Fitting the elements onto the
appliance
Clip the end of the hose to the suction inlet located at the
front of the appliance (fig.1). To remove, unclip the end using
the clip and remove.
Fix the accessory support* (27) to the notch in the self-
standing position (7) located at the rear of the vacuum
cleaner and store the accessories on top (fig. 2).
IMPORTANT! If the accessory base* is positioned
behind the appliance, it is essential to remove the
accessories in order to open the vacuum cover.
• Fit the telescopic metal tube to the end of the grip until you
hear a 'click' (fig.3) (to remove, press the tube lock button
and pull).
Fit the ERGO COMFORT SILENCE nozzle (19) to the end of
the telescopic metal tube until you hear a 'click' (fig.4) (to
remove, press the button on the nozzle and pull).
Adjust the telescopic metal tube to the required length using
the telescopic system (fig.5).
ERGONOMIC RECOMMENDATIONS
Ergonomic, the ERGO COMFORT SILENCE range
has been designed to facilitate and improve user
comfort when vacuuming.
To prevent bending over and to ensure upright
posture, make sure you:
1. Adjust the length of the ERGO COMFORT SILENCE
telescopic metal tube to your body size (fig.6).
2. Place your other hand in front of the ERGO
COMFORT grip handle (fig.7).
Fit the required accessory on to the end of the telescopic
metal tube or the grip:
- For rugs and carpets : use the 2-position nozzle (19) on
carpet position (brush retracted) or turbo brush* (fibres and
animal hair).
- For hard flat floors and hard flat floors with crevices (such
as tiled floors): use the 2-position nozzle (19) on hard floor
position (brush extended) or, for better results, use the hard
flat floor nozzle* (22a*) without the removable brush.
- For fragile hard flat floors, such as parquet, it is
recommended to use the hard flat floor nozzle (19*) or
(22b*).
IMPORTANT:
The nozzle for hard flat floor with crevices 22a* is
used to measure performance associated to the
energy label. This nozzle allows you to optimize the
dust-collection performance of your appliance on
hard flat floors with crevices.
* Depending on models: either equipment specific to cer-
tain models or available as an optional accessory.
- For corners and hard-to-reach areas: use the telescopic
crevice nozzle*.
- For upholstery and delicate surfaces: use the brush with
the grip (EASY BRUSH) or the upholstery nozzle*.
IMPORTANT: Always switch off and unplug your
vacuum cleaner before changing the accessories.
2 • Plugging in the power cord and
switching on the appliance
Unwind the power cord completely, plug in your vacuum
cleaner and press the ON/OFF pedal (fig. 8).
ATTENTION: do not operate your vacuum cleaner
without the filtration system fitted (foam, microfilter
and filter).
Adjust the suction power using the manual power control*
on the grip (fig.9):
• Position (MIN) for vacuuming delicate fabrics
(net curtains, textiles)
• Position (Medium) for everyday vacuuming for
all types of floors, which are only
slightly dirty
• Position (MAX) for vacuuming hard floors and
very dirty rugs and carpets.
3 • Storing and transporting the
appliance
After use, switch off your vacuum cleaner by pressing the
ON/OFF pedal and unplug it (fig. 10).
Rewind the power cord by pressing the power cord rewind
pedal (fig. 11).
It is easy to carry your vacuum cleaner using the handle (3).
Do not carry your appliance using the dust compartment
handle (fig.12).
When storing your vacuum cleaner, place the tube in its
storage compartment at the back of the appliance (fig.13).
You do not need to remove the accessory support* (27) to
store the accessory range.
9
EN