Dust/Chip Extraction; Starting Operation; Working Advice - Bosch GSA 18V-32 Professional Notice Originale

OBJ_BUCH-2835-002.book Page 16 Tuesday, November 15, 2016 3:41 PM
16 | English
Removing the Saw Blade (see figure B)
Swing the lever for saw blade release 4 approx. 60° in the di-
rection of the arrow and hold it in place. Pull the saw blade 1
out of the saw blade holder 18. Release the lever for saw
blade release 4 again.

Dust/Chip Extraction

 Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dust can
easily ignite.
Operation

Starting Operation

Inserting the battery (see figure A)
 Use only original Bosch lithium-ion batteries with the
voltage listed on the nameplate of your power tool.
Using other batteries can lead to injuries and pose a fire
hazard.
Insert the charged battery 10 into the battery receptacle 17
until you feel it engage.
Controlling/Presetting the Stroke Rate
Soft start allows for a precise cutting start in hard materials
(e.g. steel).
Increasing or reducing the pressure on the On/Off switch 8
enables stepless stroke-rate control of the switched-on ma-
chine.
Light pressure on the On/Off switch 8 results in a low stroke
rate. Increasing the pressure also increases the stroke rate.
With the thumbwheel for stroke rate preselection 7, the
stroke rate can be preset and changed during operation.
1: Low stroke rate
6: High stroke rate
The constant electronic control keeps the stroke rate almost
constant at no-load and under load, and ensures uniform
working performance.
The required stroke rate is dependent on the material and the
working conditions and can be determined by a practical trial.
Reducing the stroke rate is recommended when the saw
blade engages in the material as well as when sawing plastic
and aluminium.
1 609 92A 2L0 | (15.11.16)
Orbital Action Settings
The adjustable orbital action allows for optimal adaptation of
cutting speed, cutting capacity and cutting pattern to the ma-
terial being worked.
The level of orbital action can be set with rotary switch 6, even
during operation.
Orbital action switched off (level 0):
For working thin or hard material such as sheet metal or steel.
For achieving clean cutting edges.
Pendulum action level 1:
For working non-ferrous metals, hardwood, plastics or mate-
rials of medium density.
Pendulum action level 2:
For working non-ferrous metals, hardwood, plastics or mate-
rials of medium density.
For working soft materials, e. g., soft building materials, insu-
lation material, softwood, tree wood.
Pivoting and Retractable Footplate
Due to its movability, the adjustable footplate 2 adapts to the
required angular position of the surface.
Depending on the saw blade being used and the application,
the footplate 2 can be moved in lengthway direction in three
steps. Press the release button for the footplate 13 and slide
the footplate 2 to the required position. Release the footplate
release button 13 and check that the footplate 2 is firmly
latched. Slide the footplate 2 as required until it is firmly
latched.
To clean the saw blade holder 18, you can also completely
pull out the footplate 2 when the release button 11 is
pressed. After cleaning, slide the footplate back into its hold-
er until it engages.
 Do not press the release button 13 during operation.
You could lose control over the power tool and injure your-
self.
Switching On and Off
Switching on: Press the lock-off button 9 forward. Press the
On/Off switch 8 upward and keep it pressed.
Switching off: Release the On/Off switch 8.
To save energy, only switch the power tool on when using it.

Working Advice

 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
 When sawing light building materials, observe the stat-
utory provisions and the recommendations of the ma-
terial suppliers.
 Ensure that the saw blade is always longer than the di-
ameter of the workpiece, see Figure F. There is a risk of
kickback.
Check wood, press boards, building materials, etc. for foreign
objects such as nails, screws or similar, and remove them, if
required.
Bosch Power Tools