(Wet Or Gel) Battery Installation And Setting - KENT Razor Plus 24D Instructions D'utilisation

The machine can be supplied in one of the following modes:
a) Batteries (lead or gel) already installed on the
machine and ready to be used.
1. Check that the batteries are connected to the machine
with the connector (30, Fig. C).
2. Insert the ignition key (10, Fig. B) and turn it to "I"
position. If the green warning light (9a, Fig. B) turns on,
the batteries are ready to be used. If the yellow or red
warning light (9b or 9c, Fig. B) turns on, it is necessary
to charge the batteries (see procedure in Maintenance
chapter).
b) Lead batteries installed on the machine but without
liquid electrolyte.
1. Lift the cover (1, Fig. G) and make sure that the tanks (4
and 5, Fig. G) are empty, otherwise drain them through
the drain hoses (26 and 27, Fig. C).
2. Turn the handwheel (3, Fig. J) counter-clockwise until
the tank assembly is released.
3. Carefully lift the tank assembly (4, Fig. J) with the
handlebar (2, Fig. C).
4. Remove the caps (9, Fig. J) of the batteries (8).
WARNING!
Be extremely careful when working with
sulfuric acid, as it is corrosive. If it comes in
contact with skin or eyes, rinse thoroughly
with water and call a physician.
Batteries have to be filled in a well-ventilated
area.
Use protective gloves.
5. Fill up each battery element with sulfuric acid for
batteries (density 2.8 to 2.9 lb at 77°F (1.27 to 1.29 Kg at
25°C)) in accordance with the instructions specified in
the Battery manual.
The correct quantity of sulfuric acid to fill in is given in the
Battery manual.
6. To avoid damaging the floor, dry with a cloth both acid
and water on the top of the batteries after charge.
7. Let the batteries rest for a few minutes and fill in with
sulfuric acid in accordance with the instructions specified
in the Battery manual.
8. Charge the batteries (see the relevant procedure in the
Maintenance chapter).
c) Without batteries
1. Buy appropriate batteries [See the Technical Data
paragraph and the installation diagram (6, Fig. J)].
For the battery choice and installation, apply to qualified
battery retailers.
2. Install and set the batteries (WET or GEL) as described
in the following chapter, then installed the battery
charger according to the battery type.
Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01
INSTRUCTIONS FOR USE
(WET OR GEL) BATTERY INSTALLATION
AND SETTING
According to the battery type (WET or GEL) perform the
setting of the machine electronic board and of the battery
charger, operating as indicated below:
Machine setting
1. Ensure that the battery connector (30, Fig. C) is
completely disconnected.
2. Remove the handle (15, Fig. E) from the squeegee
lifting/lowering lever.
3. Unscrew the nuts (16, Fig. E), carefully remove the cover
(9), and move the panel (11) as necessary.
4. According to the type of batteries to be installed, move
the selector (4, Fig. E) to "ON" position for lead/acid
batteries, or to "OFF" position for gel batteries.
Make sure not to move the vacuum system automatic
deactivation selector (17, Fig. E).
Setting of the battery charger
5. Take the battery charger selector (3, Fig. E) to "WET"
position for lead batteries, or to "GEL" position for gel
batteries.
6. Reinstall the panel (11, Fig. E), then reinstall the cover
(9, Fig. E) again and fix it with the nuts (16).
7. Install the squeegee lifting/lowering lever handle (15,
Fig. E).
Battery installation
8. Lift the cover (1, Fig. G) and make sure that the tanks (4
and 5, Fig. G) are empty, otherwise drain them through
the drain hoses (26 and 27, Fig. C).
9. Turn the handwheel (3, Fig. J) counter-clockwise until
the tank assembly is released.
10. Carefully lift the tank assembly (4, Fig. J) with the
handlebar (2, Fig. C).
11. Install the batteries according to the diagram (6, Fig. J),
and follow the indications below according to the type of
batteries to be installed:
– For the two 12V batteries: Use the restraints supplied
with the machine;
– For the four 6V batteries: Use the restraints supplied
with the machine;
– For the 24V battery: Remove the case (7, Fig. J).
Battery charging
12. Charge the batteries (see the relevant procedure in the
Maintenance chapter).
7